Low budget plasma setup, what do I need?

More
7 years 2 months ago #142259 by andypugh
Replied by andypugh on topic Low budget plasma setup,going with 7i96
I was wondering if the problem was a wire-reduced parallel port cable (as those are quite common) but it seems to be working now?

Please Log in to join the conversation.

More
7 years 2 months ago #142260 by tecno
Replied by tecno on topic Low budget plasma setup,going with 7i96
Hi Andy, yes it works sort of. Changed the pport PCI card so now readhmid and halcmd works but now I´m stuck to set up a config. A bit confused I am how to run stepconfig for 7i90.

Please Log in to join the conversation.

More
7 years 2 months ago #142266 by andypugh
Replied by andypugh on topic Low budget plasma setup,going with 7i96
You _don't_ use Stepconfig for a 7i90. You use PncConf.

Please Log in to join the conversation.

More
7 years 2 months ago #142267 by tecno
Replied by tecno on topic Low budget plasma setup,going with 7i96
Really? There is no 7i90 in the dropdown menu.

Please Log in to join the conversation.

More
7 years 2 months ago #142270 by andypugh
Replied by andypugh on topic Low budget plasma setup,going with 7i96
Try a 7i80, then do a search and replace. It should be close.
You will also need to change the loadrt hm2_eth line to match the 7i90 line that you have already used a few times.

Please Log in to join the conversation.

More
7 years 2 months ago #143084 by tecno
Replied by tecno on topic Low budget plasma setup,going with 7i96
Slowly but this will be ready, here a test printed module2 rack in PLA. Appears to be OK so now I will print some more in PETG.
These are 250mm long with slotted backside to fit aluprofile, some sanding to do when spliced together for a longer rail.

Attachment not found

Please Log in to join the conversation.

More
7 years 2 months ago #143091 by pl7i92
Replied by pl7i92 on topic Low budget plasma setup, what do I need?
this low budget went way out of budget as it has been anounced around 1000

why not using standard RACK poinion at T10 or T5
as it is NORM like here
maedler.de/product/1643/1618/2130/zahnst...teilung-5mm-und-10mm

for plasma realy good workes fine and even no steplos at gantry gearing

Attachment not found

Please Log in to join the conversation.

More
7 years 2 months ago #143092 by tecno
Replied by tecno on topic Low budget plasma setup, what do I need?
Hmmmm. I have never said any amount on my budget only that I will use what I have on hand and try to make do with it.

Just now I do not afford to buy these racks in steel.
My car broke down = lost my power steering so I need to buy a new servo pump.
VAG parts are not cheap!

Please Log in to join the conversation.

More
7 years 2 months ago #143218 by tecno
Replied by tecno on topic Low budget plasma setup, what do I need?
So now I have racks 3x250mm mounted for Y axis. X axis racks will be ready today, 8.5hours to print each part.

Attachment not found

Please Log in to join the conversation.

More
7 years 2 months ago #143220 by tommylight
Replied by tommylight on topic Low budget plasma setup, what do I need?

tecno wrote: My car broke down = lost my power steering so I need to buy a new servo pump.
VAG parts are not cheap!

VW parts are pretty cheap here as they are the most used cars here and there are plenty of authorized and unauthorized dealers/services.
Maybe you should move here ? :)
Those racks do look nice.

Please Log in to join the conversation.

Time to create page: 0.210 seconds
Powered by Kunena Forum