Сustomization QTvcp

cmorley
Offline
Platinum Member

4 years 11 months ago #227748 by cmorley

Replied by cmorley on topic Сustomization QTvcp

Ahh yes the python2 integer/float math problem

Please Log in to join the conversation.

hottabich
Topic Author
Offline
Platinum Member

4 years 10 months ago #228349 by hottabich

Replied by hottabich on topic Сustomization QTvcp

Please tell me how to switch the mainTabWidgets page to qttouchy using PushButton on sim_panel. Thanks!

Please Log in to join the conversation.

cmorley
Offline
Platinum Member

4 years 10 months ago #228365 by cmorley

Replied by cmorley on topic Сustomization QTvcp

I can think of two options.
adding HAL pins to each.
or using ZMQ messaging between them.

Please Log in to join the conversation.

hottabich
Topic Author
Offline
Platinum Member

4 years 10 months ago #228376 by hottabich

Replied by hottabich on topic Сustomization QTvcp

ZMQ is difficult for me. With hal pin everything works. The following have been added to the handler:

Code:

self.pin_tab_manual_in = self.hal.newpin('tab-manual-in',hal.HAL_BIT, hal.HAL_IN)            self.pin_tab_manual_in.value_changed.connect(lambda s: self.tabManual(s))

And in general functions.

Code:

def tabManual(self, state):       
print state, self.current_mode       
if state:           
tab = self.w.mainTab.setCurrentIndex(TAB_Manual)

Thanks![justify]
[/justify]

Please Log in to join the conversation.

hottabich
Topic Author
Offline
Platinum Member

4 years 10 months ago #228789 by hottabich

Replied by hottabich on topic Сustomization QTvcp

The numstr.py on linuxcnc 2.8.2 file works well. On linuxcnc 2.9.0 pre. error. Please tell me how to fix this, if possible. Thanks!

Please Log in to join the conversation.

cmorley
Offline
Platinum Member

4 years 10 months ago #228796 by cmorley

Replied by cmorley on topic Сustomization QTvcp

How are you loading the program?
It's being loaded with ython2 rather then python3

Please Log in to join the conversation.

hottabich
Topic Author
Offline
Platinum Member

4 years 10 months ago #228801 by hottabich

Replied by hottabich on topic Сustomization QTvcp

Yes, it works for Python 2.7. I am trying to adapt woodpecker from python 2.7 to python 3 in linuxcnc 2.9.

Please Log in to join the conversation.

cmorley
Offline
Platinum Member

4 years 10 months ago #228818 by cmorley

Replied by cmorley on topic Сustomization QTvcp

Yes I understand.
How are you loading the numstr component in your HAL file?

Please Log in to join the conversation.

hottabich
Topic Author
Offline
Platinum Member

4 years 10 months ago #228821 by hottabich

Replied by hottabich on topic Сustomization QTvcp

loadusr -Wn numstr python numstr.py
net line motion.program-line => numstr.in => woodpecker.line_number
And it is necessary
loadusr -Wn numstr python3 numstr.py
Not enough now
woodpecker.line_number
I will think. Thank you very much!
Everything worked out. Thanks again!

Code:

loadusr -Wn numstr python3 numstr.py
net line  => woodpecker.lcdnumber_2

Please Log in to join the conversation.

hottabich
Topic Author
Offline
Platinum Member

4 years 10 months ago #228853 by hottabich

Replied by hottabich on topic Сustomization QTvcp

Is it possible to apply segmentStyle (Flat) somehow for DroLabel? Thanks!

Please Log in to join the conversation.

Time to create page: 0.252 seconds