Linux Startet in der Eingabeaufforderung

More
02 Jun 2023 10:41 #272691 by Muecke
Hallo zusammen,

nach einer längeren Pause wollte ich meinen aktuellen Rechner hochfahren, aber jetzt startet Linux in der Eingabeaufforderung und nicht in der GUI.

Woran kann das liegen bzw. was muss ich tun, damit ich in die GUI komme und wie kann ich das einstellen, dass es immer in der GUI startet?

Habe die ISO hier aus dem Downloadbereich installiert.

Gruß Mücke

Please Log in or Create an account to join the conversation.

More
02 Jun 2023 11:08 #272698 by spicer
Also ist es ein Debian Bullseye oder Buster?

Please Log in or Create an account to join the conversation.

More
02 Jun 2023 11:15 #272703 by tommylight
Die officiele 2.8.4 ist Buster.
Schrieb
starx
Was gibt?
The following user(s) said Thank You: Muecke

Please Log in or Create an account to join the conversation.

More
02 Jun 2023 11:22 #272705 by spicer
The following user(s) said Thank You: Muecke

Please Log in or Create an account to join the conversation.

More
02 Jun 2023 11:31 #272707 by Muecke
DebienCNC 4.19.0-17-rt-amd64 #1 ...(2021-06-21)

$:startx
=> Bild
sorry ich weis nicht was da wichtig ist und was nicht daher das Bild :-(

 
Attachments:

Please Log in or Create an account to join the conversation.

More
02 Jun 2023 11:35 #272708 by rodw
if startx does not work on its own try:
sudo apt install task-xfce-desktop
startx
 

Please Log in or Create an account to join the conversation.

More
02 Jun 2023 11:42 #272711 by Muecke
Paket nicht gefunden :-(
 
Attachments:

Please Log in or Create an account to join the conversation.

More
02 Jun 2023 11:44 - 19 Jun 2023 02:39 #272712 by rodw
Seems something wrong with install. on one line it says kernel 4.19 (buster) and on another (kernel 5.10) Bullseye.

If you start again, download this ISO (Debian Bookworm RC4)
cdimage.debian.org/cdimage/bookworm_di_r...c4-amd64-netinst.iso
And follow my instructions which were based on Debian Bookworm RC3 that is now superceded.
vmnet.com.au/linuxcnc/getting-linuxcnc.html


This is now superceded as its in the 2.9 documents now. Not sure how the translations work.
Please refer to this link instead. linuxcnc.org/docs/2.9/html/getting-start...etting-linuxcnc.html
Last edit: 19 Jun 2023 02:39 by rodw.
The following user(s) said Thank You: Muecke

Please Log in or Create an account to join the conversation.

More
02 Jun 2023 11:54 #272714 by Muecke
Ich muss neu installieren?
I need to reinstall?

Please Log in or Create an account to join the conversation.

More
02 Jun 2023 12:15 #272715 by tommylight
Try booting from USB.
The issue might be caused by failing hard drive, bad memory, bad power supply, or bad graphic card.
But first check that the monitor cable is properly seated on PC and monitor.

Please Log in or Create an account to join the conversation.

Time to create page: 0.135 seconds
Powered by Kunena Forum