Forum Menu

Debian 12 - Bookworm Live installer ISO for linuxcnc (x86_64)

More
3 years 1 month ago #281158 by rodw
Replied by rodw on topic Debian 12 - Bookworm Live installer ISO for linuxcnc (x86_64)
I also grabbed the default /etc/apt/sources.list file the installer starts with
drive.google.com/file/d/1dBE7uNtwHYEHpdB...BzX/view?usp=sharing
Just in case you don't have internet when you install
Repeated here for good luck
Code:
deb http://deb.debian.org/debian bookworm main contrib non-free non-free-firmware deb-src http://deb.debian.org/debian bookworm main contrib non-free non-free-firmware deb http://deb.debian.org/debian-security bookworm-security main contrib non-free non-free-firmware deb-src http://deb.debian.org/debian-security bookworm-security main contrib non-free non-free-firmware deb http://deb.debian.org/debian bookworm-updates main contrib non-free non-free-firmware deb-src http://deb.debian.org/debian bookworm-updates main contrib non-free non-free-firmware

Please Log in or Create an account to join the conversation.

More
3 years 1 month ago #281267 by radicus
Replied by radicus on topic Debian 12 - Bookworm Live installer ISO for linuxcnc (x86_64)
Installs successfully but on reboot, does not  boot from hard disk.   Modified every UEFI option I could think of.


Live CD option boots up no problem

 

Please Log in or Create an account to join the conversation.

More
3 years 1 month ago #281268 by rodw
Replied by rodw on topic Debian 12 - Bookworm Live installer ISO for linuxcnc (x86_64)

Installs successfully but on reboot, does not  boot from hard disk.   Modified every UEFI option I could think of.


Live CD option boots up no problem


 
What PC hardware do you have?
Do you see the Grub menu?
If you open the boot menu (F9 for me but it changes with  PC brand) , can you select the Linux volume?
Its going to be a while before I can try installing it on a real PC.

Please Log in or Create an account to join the conversation.

More
3 years 1 month ago #281270 by radicus
Replied by radicus on topic Debian 12 - Bookworm Live installer ISO for linuxcnc (x86_64)
Dell precision 5810
xeon e5
no grub menu
i get can get into bios and create a boot option,  then navigate to /efi … and select grubx64

Please Log in or Create an account to join the conversation.

More
3 years 1 month ago #281417 by radicus
Replied by radicus on topic Debian 12 - Bookworm Live installer ISO for linuxcnc (x86_64)
Not a problem with this installer. Can’t get the official installer to boot in legacy or efi. What a pain. I have 4 Dell machines I saved off the recycling palette. They work with buster no problem

Please Log in or Create an account to join the conversation.

More
3 years 1 month ago #281418 by rodw
Replied by rodw on topic Debian 12 - Bookworm Live installer ISO for linuxcnc (x86_64)
Can you try the official Debian Installer?
www.debian.org/

If that loads, then you can install linuxcnc by folowing these steps
linuxcnc.org/docs/2.9/html/getting-start...etting-linuxcnc.html
And you will end up with the same place as the installer.

I know your frustration. I have 2 small PC's that I can't get boo out of anymore

Please Log in or Create an account to join the conversation.

Time to create page: 0.224 seconds
Powered by Kunena Forum