1. Forum
  3. Search

Advanced Search

Search Results (Searched for: )

  • tommylight
  • tommylight's Avatar
24 Mar 2025 23:06
Replied by tommylight on topic Linux_Mint_22.1_LinuxCNC_2.10.iso

Linux_Mint_22.1_LinuxCNC_2.10.iso

Category: Installing LinuxCNC

The only problem I'm having is the Software Manager hangs up and says "Loading please wait".

In a terminal
sudo apt install flatpak
That is the reason software manager does not start and i mentioned that i removed it as i never use it, i use terminal exclusively.
  • Vector
  • Vector's Avatar
24 Mar 2025 22:41 - 24 Mar 2025 22:43
Replied by Vector on topic Is there a "no go zone" feature of any kind?

Is there a "no go zone" feature of any kind?

Category: General LinuxCNC Questions

Thanks again!

That last suggesting, to use hal to monitor it...

I'm familiar with setting up the game-pad pendant, and so my recollection is that you add some mux-es and ands and ors to the servo thread, and check for buttons and do the bit-math until you come up with a speed to feed into the jogging speed.

So my first thought is kinda redux that thinking: use the ands and ors and current position pins and create a section in the .ini file for limits which the ands and ors are comparing, and have the logic come up with a on/off value which gets net-ed into the Estop pin.

I think it would either have to
A: anticipate the movement somehow, (because if it used the current position, once you tripped it, you'd have no way to un-trip it. {evil grin}) and I'm clueless on how that would work,
or,
B: it would need some 'override' button, say on the jogging device, to ignore the limits and allow moving it anyway. (That's easy to imagine how it works with a final or statement.)

So the second option seems easier.

With second option, I'm thinking the e-stop button on the GUI would just trip on, everything would stop (you are spanked). Then you'd have use your pendant with override pressed to move somewhere where the e-stop button on the GUI trips back off. Then figure out how to avoid that spanking.

Is there another/better approach that comes to mind?

(I'm probably not counting the risk high enough to actually make it to the proactive action of doing this now... when I crash something badly, then I'll probably do it. Sigh. Sometimes it sucks knowing one's own psychology.)
  • PCW
  • PCW's Avatar
24 Mar 2025 22:38
Replied by PCW on topic 7i76EU Requirements

7i76EU Requirements

Category: Driver Boards

Pretty sure 2.9.3 should be OK (7I76EU support was added 2 years ago)

Mesaflash >3.5.2
  • scotth
  • scotth
24 Mar 2025 22:33
Replied by scotth on topic Linux_Mint_22.1_LinuxCNC_2.10.iso

Linux_Mint_22.1_LinuxCNC_2.10.iso

Category: Installing LinuxCNC

You are right, Rufus is the way to go on building the USB drive.
The only problem I'm having is the Software Manager hangs up and says "Loading please wait".

Linuxcnc loaded my old config files and started with no problems.
  • mmt
  • mmt
24 Mar 2025 22:31 - 24 Mar 2025 22:34
Replied by mmt on topic neeed help with additional pwm 6i25 and 7i76

neeed help with additional pwm 6i25 and 7i76

Category: Basic Configuration

sorry spoke too soon

there are 4 pwm in the terminal command but hal stop on the pwm freq line. i tried it with a hyphen and an underscore

here is my relevant info
Configuration Name: HOSTMOT2

General configuration information:

  BoardName : MESA5I25
  FPGA Size: 9 KGates
  FPGA Pins: 144
  Number of IO Ports: 2
  Width of one I/O port: 17
  Clock Low frequency: 33.3333 MHz
  Clock High frequency: 200.0000 MHz
  IDROM Type: 3
  Instance Stride 0: 4
  Instance Stride 1: 64
  Register Stride 0: 256
  Register Stride 1: 256

Modules in configuration:

  Module: DPLL
  There are 1 of DPLL in configuration
  Version: 0
  Registers: 7
  BaseAddress: 7000
  ClockFrequency: 33.333 MHz
  Register Stride: 256 bytes
  Instance Stride: 4 bytes

  Module: WatchDog
  There are 1 of WatchDog in configuration
  Version: 0
  Registers: 3
  BaseAddress: 0C00
  ClockFrequency: 33.333 MHz
  Register Stride: 256 bytes
  Instance Stride: 4 bytes

  Module: IOPort
  There are 2 of IOPort in configuration
  Version: 0
  Registers: 5
  BaseAddress: 1000
  ClockFrequency: 33.333 MHz
  Register Stride: 256 bytes
  Instance Stride: 4 bytes

  Module: PWM
  There are 4 of PWM in configuration
  Version: 0
  Registers: 5
  BaseAddress: 4100
  ClockFrequency: 200.000 MHz
  Register Stride: 256 bytes
  Instance Stride: 4 bytes

  Module: QCount
  There are 2 of QCount in configuration
  Version: 2
  Registers: 5
  BaseAddress: 3000
  ClockFrequency: 33.333 MHz
  Register Stride: 256 bytes
  Instance Stride: 4 bytes

  Module: SSerial
  There are 1 of SSerial in configuration
  Version: 0
  Registers: 6
  BaseAddress: 5B00
  ClockFrequency: 33.333 MHz
  Register Stride: 256 bytes
  Instance Stride: 64 bytes

  Module: StepGen
  There are 6 of StepGen in configuration
  Version: 2
  Registers: 10
  BaseAddress: 2000
  ClockFrequency: 33.333 MHz
  Register Stride: 256 bytes
  Instance Stride: 4 bytes

  Module: LED
  There are 1 of LED in configuration
  Version: 0
  Registers: 1
  BaseAddress: 0200
  ClockFrequency: 33.333 MHz
  Register Stride: 256 bytes
  Instance Stride: 4 bytes

Configuration pin-out:

IO Connections for P3
DB25 pin#             I/O   Pri. func    Sec. func        Chan     Sec. Pin func   Sec. Pin Dir

 1                      0   IOPort       StepGen          0        Dir/Table2      (Out)
14                      1   IOPort       StepGen          0        Step/Table1     (Out)
 2                      2   IOPort       StepGen          1        Dir/Table2      (Out)
15                      3   IOPort       StepGen          1        Step/Table1     (Out)
 3                      4   IOPort       StepGen          2        Dir/Table2      (Out)
16                      5   IOPort       StepGen          2        Step/Table1     (Out)
 4                      6   IOPort       PWM              0        Dir             (Out)
17                      7   IOPort       PWM              0        PWM             (Out)
 5                      8   IOPort       PWM              1        Dir             (Out)
 6                      9   IOPort       PWM              1        PWM             (Out)
 7                     10   IOPort       SSerial          0        TXData0         (Out)
 8                     11   IOPort       SSerial          0        RXData0         (In)
 9                     12   IOPort       SSerial          0        TXData1         (Out)
10                     13   IOPort       SSerial          0        RXData1         (In)
11                     14   IOPort       QCount           0        Quad-IDX        (In)
12                     15   IOPort       QCount           0        Quad-B          (In)
13                     16   IOPort       QCount           0        Quad-A          (In)

IO Connections for P2
DB25 pin#             I/O   Pri. func    Sec. func        Chan     Sec. Pin func   Sec. Pin Dir

 1                     17   IOPort       StepGen          3        Dir/Table2      (Out)
14                     18   IOPort       StepGen          3        Step/Table1     (Out)
 2                     19   IOPort       StepGen          4        Dir/Table2      (Out)
15                     20   IOPort       StepGen          4        Step/Table1     (Out)
 3                     21   IOPort       StepGen          5        Dir/Table2      (Out)
16                     22   IOPort       StepGen          5        Step/Table1     (Out)
 4                     23   IOPort       PWM              2        Dir             (Out)
17                     24   IOPort       PWM              2        PWM             (Out)
 5                     25   IOPort       PWM              3        Dir             (Out)
 6                     26   IOPort       PWM              3        PWM             (Out)
 7                     27   IOPort       SSerial          0        TXData2         (Out)
 8                     28   IOPort       SSerial          0        RXData2         (In)
 9                     29   IOPort       SSerial          0        TXData3         (Out)
10                     30   IOPort       SSerial          0        RXData3         (In)
11                     31   IOPort       QCount           1        Quad-IDX        (In)
12                     32   IOPort       QCount           1        Quad-B          (In)
13                     33   IOPort       QCount           1        Quad-A          (In)


loadrt [KINS]KINEMATICS
loadrt [EMCMOT]EMCMOT servo_period_nsec=[EMCMOT]SERVO_PERIOD num_joints=[KINS]JOINTS
loadrt hostmot2
loadrt hm2_pci config="num_encoders=1 num_pwmgens=1 num_stepgens=4 sserial_port_0=00xxxxxx"
setp    hm2_5i25.0.watchdog.timeout_ns 5000000
loadrt pid names=pid.x,pid.y,pid.z,pid.a,pid.s
loadrt pwmgen output_type=0

addf hm2_5i25.0.read          servo-thread
addf motion-command-handler   servo-thread
addf motion-controller        servo-thread
addf pid.x.do-pid-calcs       servo-thread
addf pid.y.do-pid-calcs       servo-thread
addf pid.z.do-pid-calcs       servo-thread
addf pid.a.do-pid-calcs       servo-thread
addf pid.s.do-pid-calcs       servo-thread
addf hm2_5i25.0.write         servo-thread

# external output signals

net shutter-output      => hm2_5i25.0.7i76.0.0.output-00
net laser-output        => hm2_5i25.0.7i76.0.0.output-01

# --- LASER POWER ---
setp   hm2_5i25.0.pwmgen.0.pwm_freq 1000
setp   hm2_5i25.0.pwmgen.0.scale 100
net pwm-output hm2_5i25.0.pwmgen.0
net pwm-enable <= motion.motion-enabled  => hm2_5i25.0.pwmgen.0.enable
  • aharner
  • aharner
24 Mar 2025 22:31
Replied by aharner on topic Connecting Mesa 7i76 to Sprint 1200 DC Controller

Connecting Mesa 7i76 to Sprint 1200 DC Controller

Category: General LinuxCNC Questions

Sir, thank you for your immediate response, I had the first two pins figured out but the last ones I needed clarification. Time to get her spinning. Can't thank you enough.
  • D Jensen
  • D Jensen
24 Mar 2025 22:29
Replied by D Jensen on topic Retrofitting a 1986 Maho MH400E

Retrofitting a 1986 Maho MH400E

Category: Milling Machines

I'm wrong again. It occurred to me that if your one has the hand wheel on the top slide then you will have to pull that whole assembly out before pulling out the quill as the rack teeth don't go the full length of the quill. I don't know how you do that on your version and my manual for the vertical quill didn't have an explanation that there was a scotch key retaining it.
Cheers,
David
  • PCW
  • PCW's Avatar
24 Mar 2025 22:27
Replied by PCW on topic Connecting Mesa 7i76 to Sprint 1200 DC Controller

Connecting Mesa 7i76 to Sprint 1200 DC Controller

Category: General LinuxCNC Questions

So

7I76EU TB4     DRIVE

1 SPINDLE-      2 MIN
2 SPINOUT       3 IP
3 SPINDLE+     1 +10V
5 ENA-             4 COM
6 ENA+            5 RUN

Note that some or all of these connections may be at line potential
so make sure you do not touch them or allow them to connect to
any low voltage signal.


 
  • mmt
  • mmt
24 Mar 2025 22:24
Replied by mmt on topic neeed help with additional pwm 6i25 and 7i76

neeed help with additional pwm 6i25 and 7i76

Category: Basic Configuration

that worked sorry for the mix up

thank you
  • PCW
  • PCW's Avatar
24 Mar 2025 22:16
Replied by PCW on topic 7I97T joint following error

7I97T joint following error

Category: General LinuxCNC Questions

Yes, at motor 2400 RPM the ballscrew would turn at 1200 RPM (20 TPS)
and 20 TPS * 0.2 IPT = 4 IPS
  • PCW
  • PCW's Avatar
24 Mar 2025 22:06
Replied by PCW on topic neeed help with additional pwm 6i25 and 7i76

neeed help with additional pwm 6i25 and 7i76

Category: Basic Configuration

That's the plasma config, the configuration with 2 PWMgens per 7I76 is:

5i25_7i76x2_2pd.bit


 
  • aharner
  • aharner
24 Mar 2025 22:03
Replied by aharner on topic Connecting Mesa 7i76 to Sprint 1200 DC Controller

Connecting Mesa 7i76 to Sprint 1200 DC Controller

Category: General LinuxCNC Questions

Yes I do.  I have the right hand side of the Sprint all taken care of, its the low voltage/control side that I cant figure out.  Thanks in advance for your help.
  • mmt
  • mmt
24 Mar 2025 21:51
Replied by mmt on topic neeed help with additional pwm 6i25 and 7i76

neeed help with additional pwm 6i25 and 7i76

Category: Basic Configuration

yes i did power it 
  • Evgen
  • Evgen
24 Mar 2025 21:49
Replied by Evgen on topic scurve trajectory planner

scurve trajectory planner

Category: General LinuxCNC Questions

Hello! I have intersting problem. I use solidcam iMachining procedures for milling. With ordinary TP I have some strange deaccelerations and my servos don't like it. Then I check your tp, it try to stop every g-code segment. I can't understand where is problem. Help me, please. White screenshot - new tp, black - ordinary tp. All tests on pictures are in simulation.
  • Tinker
  • Tinker
24 Mar 2025 21:45
Replied by Tinker on topic 7I97T joint following error

7I97T joint following error

Category: General LinuxCNC Questions

Basically 4 IPS would be my scale number if I'm understanding you correctly..
Displaying 16831 - 16845 out of 18578 results.
  1. Forum
  3. Search
Time to create page: 0.346 seconds
Powered by Kunena Forum