Advanced Search

Search by Keyword Keywords:

Search Options

Find Posts from

Sort Results by

Search at a specific date

Jump to Result Number

Search in Categories Also search in sub-categories

Search Results (Searched for: )

Ismacr63
Ismacr63

15 Nov 2024 17:27

Replied by Ismacr63 on topic coolant mist pulses

coolant mist pulses

Category: QtPyVCP

PCW wrote:
Yes, all this will work on a parallel port.

something like this:

loadrt siggen
addf siggen.0.update servo-thread
setp siggen.0.frequency .1 # 10 second period)
loadrt oneshot
addf oneshot.0 servo-thread
setp oneshot.0.width 2 # 2 second on time
loadrt not
addf not.0 servo-thread
net cool-trigger siggen.0.clock oneshot.0.in
net coolant-out oneshot.0.out [some_parallel_port_pin]
net coolant-on not.0.in
net gate-coolant not.0.out oneshot.0.reset siggen.0.reset # when coolant is off, reset both siggen and oneshot

Tried to test it but received an error. If I remove the lines that I have added in hal linuxcnc starts normally

PCW

15 Nov 2024 17:27 - 15 Nov 2024 17:30

Replied by PCW on topic Suggestion for a PCI EPP card for 7i43

Suggestion for a PCI EPP card for 7i43

Category: General LinuxCNC Questions

You might try reversing the addresses based on the lspci order:

Region 0: I/O ports at d010
Region 1: I/O ports at d000

It may also be that the 7I43 is damaged

juliankoenig87
juliankoenig87

15 Nov 2024 17:18

Replied by juliankoenig87 on topic Suggestion for a PCI EPP card for 7i43

Suggestion for a PCI EPP card for 7i43

Category: General LinuxCNC Questions

Mhmmm.
loadrt hm2_7i43 ioaddr=0xd000 ioaddr_hi=0xd010 epp_wide=0 config="firmware=hm2/7i43-4/SVST4_4.BIT num_encoders=0 num_pwmgens=0 num_stepgens=3"
gives me:

Warning: Spoiler!

PCW

15 Nov 2024 17:01 - 15 Nov 2024 17:12

Replied by PCW on topic Suggestion for a PCI EPP card for 7i43

Suggestion for a PCI EPP card for 7i43

Category: General LinuxCNC Questions

0xd400 cannot be a valid address as its not listed by lspci

that is, "ioaddr_hi=0xd010" should be tested

Also hm2/7i43-2/SVST4_4.BIT is a bitfile for a 7I43-2, but you have a 7I43-4

juliankoenig87
juliankoenig87

15 Nov 2024 16:59

Replied by juliankoenig87 on topic Suggestion for a PCI EPP card for 7i43

Suggestion for a PCI EPP card for 7i43

Category: General LinuxCNC Questions

I can get some strange results:
loadrt hm2_7i43 ioaddr=0xd000 ioaddr_hi=0xd400 epp_wide=0 config="firmware=hm2/7i43-2/SVST4_4.BIT

Gives me:
No parport registered at 0xd000. This is not always an error. Continuing.
hm2/hm2_7i43.0: invalid cookie, got 0x00000000, expected 0x55AACAFE
hm2/hm2_7i43.0: FPGA failed to initialize, or unexpected firmware?
hm2_7i43.0: board at (ioaddr=0xD000, ioaddr_hi=0xD400, epp_wide OFF) not found!
hm2_7i43: rtapi_app_main: Invalid argument (-22)

If I change to:
loadrt hm2_7i43 ioaddr=0xd010 ioaddr_hi=0xd410 epp_wide=0 config="firmware=hm2/7i43-2/SVST4_4.BIT

I have to change to the 7i43-4 firmware because linuxcnc said thats tghe wrong one. Wit 000 and 400 it is vise versa...

Axolito

15 Nov 2024 16:54

Replied by Axolito on topic Unwanted actions with a touch screen

Unwanted actions with a touch screen

Category: Gmoccapy

This version doesn't have the jog buttons, but the problem was the same when they were displayed.

juliankoenig87
juliankoenig87

15 Nov 2024 16:42

Replied by juliankoenig87 on topic Suggestion for a PCI EPP card for 7i43

Suggestion for a PCI EPP card for 7i43

Category: General LinuxCNC Questions

Ok. that is new:

cnc@linuxcnc:~$ sudo mesaflash --epp --device 7i43 --addr 0xd000
[sudo] Passwort für cnc:

EPP device 7I43 at 0xD000:0xD400

PCW

15 Nov 2024 16:42

Replied by PCW on topic Suggestion for a PCI EPP card for 7i43

Suggestion for a PCI EPP card for 7i43

Category: General LinuxCNC Questions

might be 0xd000 low 0xd010 high

juliankoenig87
juliankoenig87

15 Nov 2024 16:40

Replied by juliankoenig87 on topic Suggestion for a PCI EPP card for 7i43

Suggestion for a PCI EPP card for 7i43

Category: General LinuxCNC Questions

So. d010 and d000 ?

I tried 0xd000 without success.

juliankoenig87
juliankoenig87

15 Nov 2024 16:37

Replied by juliankoenig87 on topic Suggestion for a PCI EPP card for 7i43

Suggestion for a PCI EPP card for 7i43

Category: General LinuxCNC Questions

lspci -vv:

Warning: Spoiler!

00:00.0 Host bridge: Intel Corporation Core Processor DMI (rev 11)
   Subsystem: Lenovo Core Processor DMI
   Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Capabilities: <access denied>

00:03.0 PCI bridge: Intel Corporation Core Processor PCI Express Root Port 1 (rev 11) (prog-if 00 [Normal decode])
   Subsystem: Lenovo Core Processor PCI Express Root Port 1
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0, Cache Line Size: 64 bytes
   Interrupt: pin A routed to IRQ 28
   Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
   I/O behind bridge: e000-efff [size=4K] [16-bit]
   Memory behind bridge: fa000000-fb0fffff [size=17M] [32-bit]
   Prefetchable memory behind bridge: c0000000-d1ffffff [size=288M] [32-bit]
   Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
   BridgeCtl: Parity- SERR+ NoISA- VGA+ VGA16+ MAbort- >Reset- FastB2B-
       PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
   Capabilities: <access denied>
   Kernel driver in use: pcieport

00:08.0 System peripheral: Intel Corporation Core Processor System Management Registers (rev 11)
   Subsystem: Device 00aa:0059
   Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Capabilities: <access denied>

00:08.1 System peripheral: Intel Corporation Core Processor Semaphore and Scratchpad Registers (rev 11)
   Subsystem: Device 00aa:0059
   Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Capabilities: <access denied>

00:08.2 System peripheral: Intel Corporation Core Processor System Control and Status Registers (rev 11)
   Subsystem: Device 00aa:0059
   Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Capabilities: <access denied>

00:08.3 System peripheral: Intel Corporation Core Processor Miscellaneous Registers (rev 11)
   Subsystem: Device 00aa:0059
   Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:10.0 System peripheral: Intel Corporation Core Processor QPI Link (rev 11)
   Subsystem: Device 00aa:0059
   Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:10.1 System peripheral: Intel Corporation Core Processor QPI Routing and Protocol Registers (rev 11)
   Subsystem: Device 00aa:0059
   Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06)
   Subsystem: Lenovo 5 Series/3400 Series Chipset HECI Controller
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Interrupt: pin A routed to IRQ 32
   Region 0: Memory at fb145000 (64-bit, non-prefetchable)
   Capabilities: <access denied>
   Kernel driver in use: mei_me
   Kernel modules: mei_me

00:19.0 Ethernet controller: Intel Corporation 82578DM Gigabit Network Connection (rev 06)
   DeviceName: Onboard LAN
   Subsystem: Lenovo 82578DM Gigabit Network Connection
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Interrupt: pin A routed to IRQ 29
   Region 0: Memory at fb120000 (32-bit, non-prefetchable) [size=128K]
   Region 1: Memory at fb144000 (32-bit, non-prefetchable) [size=4K]
   Region 2: I/O ports at f040
   Capabilities: <access denied>
   Kernel driver in use: e1000e
   Kernel modules: e1000e

00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) (prog-if 20 [EHCI])
   Subsystem: Lenovo 5 Series/3400 Series Chipset USB2 Enhanced Host Controller
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Interrupt: pin A routed to IRQ 16
   Region 0: Memory at fb143000 (32-bit, non-prefetchable) [size=1K]
   Capabilities: <access denied>
   Kernel driver in use: ehci-pci
   Kernel modules: ehci_pci

00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) (prog-if 20 [EHCI])
   Subsystem: Lenovo 5 Series/3400 Series Chipset USB2 Enhanced Host Controller
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Interrupt: pin A routed to IRQ 23
   Region 0: Memory at fb142000 (32-bit, non-prefetchable) [size=1K]
   Capabilities: <access denied>
   Kernel driver in use: ehci-pci
   Kernel modules: ehci_pci

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a6) (prog-if 01 [Subtractive decode])
   Subsystem: Lenovo 82801 PCI Bridge
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
   I/O behind bridge: d000-dfff [size=4K] [16-bit]
   Memory behind bridge: [disabled] [32-bit]
   Prefetchable memory behind bridge: [disabled] [64-bit]
   Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
   BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
       PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
   Capabilities: <access denied>

00:1f.0 ISA bridge: Intel Corporation Q57 Chipset LPC Interface Controller (rev 06)
   Subsystem: Lenovo Q57 Chipset LPC Interface Controller
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Capabilities: <access denied>
   Kernel driver in use: lpc_ich
   Kernel modules: lpc_ich

00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) (prog-if 01 [AHCI 1.0])
   Subsystem: Lenovo 5 Series/3400 Series Chipset 6 port SATA AHCI Controller
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
   Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Interrupt: pin B routed to IRQ 30
   Region 0: I/O ports at f090
   Region 1: I/O ports at f080
   Region 2: I/O ports at f070
   Region 3: I/O ports at f060
   Region 4: I/O ports at f020
   Region 5: Memory at fb141000 (32-bit, non-prefetchable) [size=2K]
   Capabilities: <access denied>
   Kernel driver in use: ahci
   Kernel modules: ahci

00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06)
   Subsystem: Lenovo 5 Series/3400 Series Chipset SMBus Controller
   Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Interrupt: pin C routed to IRQ 18
   Region 0: Memory at fb140000 (64-bit, non-prefetchable)
   Region 4: I/O ports at f000
   Kernel driver in use: i801_smbus
   Kernel modules: i2c_i801

01:00.0 VGA compatible controller: NVIDIA Corporation GT218 [GeForce 310] (rev a2) (prog-if 00 [VGA controller])
   Subsystem: Micro-Star International Co., Ltd. [MSI] GT218 [GeForce 310]
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0, Cache Line Size: 64 bytes
   Interrupt: pin A routed to IRQ 31
   Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
   Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
   Region 3: Memory at d0000000 (64-bit, prefetchable) [size=32M]
   Region 5: I/O ports at e000
   Expansion ROM at 000c0000 [disabled] [size=128K]
   Capabilities: <access denied>
   Kernel driver in use: nouveau
   Kernel modules: nouveau

01:00.1 Audio device: NVIDIA Corporation High Definition Audio Controller (rev a1)
   Subsystem: Micro-Star International Co., Ltd. [MSI] High Definition Audio Controller
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0, Cache Line Size: 64 bytes
   Interrupt: pin B routed to IRQ 17
   Region 0: Memory at fb080000 (32-bit, non-prefetchable) [size=16K]
   Capabilities: <access denied>
   Kernel driver in use: snd_hda_intel
   Kernel modules: snd_hda_intel

02:0a.0 Parallel controller: Timedia Technology Co Ltd SUN1888 (Dual IEEE1284 parallel port) (rev 01) (prog-if 02 [ECP])
   Subsystem: Timedia Technology Co Ltd PAR4008A
   Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Interrupt: pin A routed to IRQ 20
   Region 0: I/O ports at d010
   Region 1: I/O ports at d000
   Kernel driver in use: parport_pc
   Kernel modules: parport_pc

ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-Core Registers (rev 04)
   Subsystem: Intel Corporation Core Processor QuickPath Architecture Generic Non-Core Registers
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0

ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 04)
   Subsystem: Intel Corporation Core Processor QuickPath Architecture System Address Decoder
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0

ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 04)
   Subsystem: Intel Corporation Core Processor QPI Link 0
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Kernel driver in use: i7core_edac
   Kernel modules: i7core_edac

ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 04)
   Subsystem: Intel Corporation Core Processor QPI Physical 0
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0

ff:03.0 Host bridge: Intel Corporation Core Processor Integrated Memory Controller (rev 04)
   Subsystem: Intel Corporation Core Processor Integrated Memory Controller
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0

ff:03.1 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Target Address Decoder (rev 04)
   Subsystem: Intel Corporation Core Processor Integrated Memory Controller Target Address Decoder
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0

ff:03.4 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Test Registers (rev 04)
   Subsystem: Intel Corporation Core Processor Integrated Memory Controller Test Registers
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0

ff:04.0 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Control Registers (rev 04)
   Subsystem: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Control Registers
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0

ff:04.1 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Address Registers (rev 04)
   Subsystem: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Address Registers
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0

ff:04.2 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Rank Registers (rev 04)
   Subsystem: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Rank Registers
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0

ff:04.3 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Thermal Control Registers (rev 04)
   Subsystem: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Thermal Control Registers
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0

ff:05.0 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Control Registers (rev 04)
   Subsystem: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Control Registers
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0

ff:05.1 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Address Registers (rev 04)
   Subsystem: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Address Registers
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0

ff:05.2 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Rank Registers (rev 04)
   Subsystem: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Rank Registers
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0

ff:05.3 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Thermal Control Registers (rev 04)
   Subsystem: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Thermal Control Registers
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0

PCW

15 Nov 2024 16:10

Replied by PCW on topic Suggestion for a PCI EPP card for 7i43

Suggestion for a PCI EPP card for 7i43

Category: General LinuxCNC Questions

You would need the

lspci -vv

option to show addresses

juliankoenig87
juliankoenig87

15 Nov 2024 16:08

Replied by juliankoenig87 on topic Suggestion for a PCI EPP card for 7i43

Suggestion for a PCI EPP card for 7i43

Category: General LinuxCNC Questions

Ok. Everytime I use only the terminal I can get a connection to the 7i43.

Once I try to start linuxcnc I get an error. After that the pc freezes when I try to reacg for the card by the terminal.

PCW

15 Nov 2024 16:04

Replied by PCW on topic Only one of the gantry joints move

Only one of the gantry joints move

Category: Basic Configuration

Can you post your hal/ini files?

juliankoenig87
juliankoenig87

15 Nov 2024 16:00 - 15 Nov 2024 16:05

Replied by juliankoenig87 on topic Suggestion for a PCI EPP card for 7i43

Suggestion for a PCI EPP card for 7i43

Category: General LinuxCNC Questions

Thank you for the support.

lspci:

Warning: Spoiler!

00:00.0 Host bridge: Intel Corporation Core Processor DMI (rev 11)
00:03.0 PCI bridge: Intel Corporation Core Processor PCI Express Root Port 1 (rev 11)
00:08.0 System peripheral: Intel Corporation Core Processor System Management Registers (rev 11)
00:08.1 System peripheral: Intel Corporation Core Processor Semaphore and Scratchpad Registers (rev 11)
00:08.2 System peripheral: Intel Corporation Core Processor System Control and Status Registers (rev 11)
00:08.3 System peripheral: Intel Corporation Core Processor Miscellaneous Registers (rev 11)
00:10.0 System peripheral: Intel Corporation Core Processor QPI Link (rev 11)
00:10.1 System peripheral: Intel Corporation Core Processor QPI Routing and Protocol Registers (rev 11)
00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06)
00:19.0 Ethernet controller: Intel Corporation 82578DM Gigabit Network Connection (rev 06)
00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06)
00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a6)
00:1f.0 ISA bridge: Intel Corporation Q57 Chipset LPC Interface Controller (rev 06)
00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06)
00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06)
01:00.0 VGA compatible controller: NVIDIA Corporation GT218 [GeForce 310] (rev a2)
01:00.1 Audio device: NVIDIA Corporation High Definition Audio Controller (rev a1)
02:0a.0 Parallel controller: Timedia Technology Co Ltd SUN1888 (Dual IEEE1284 parallel port) (rev 01)
ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-Core Registers (rev 04)
ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 04)
ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 04)
ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 04)
ff:03.0 Host bridge: Intel Corporation Core Processor Integrated Memory Controller (rev 04)
ff:03.1 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Target Address Decoder (rev 04)
ff:03.4 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Test Registers (rev 04)
ff:04.0 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Control Registers (rev 04)
ff:04.1 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Address Registers (rev 04)
ff:04.2 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Rank Registers (rev 04)
ff:04.3 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Thermal Control Registers (rev 04)
ff:05.0 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Control Registers (rev 04)
ff:05.1 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Address Registers (rev 04)
ff:05.2 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Rank Registers (rev 04)
ff:05.3 Host bridge: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Thermal Control Registers (rev 04)

It is a Sunix 4008T card. I have a Sunix PAR6408A card for pci-e, but cant use it.
Tried also "cat /proc/ioports":

Warning: Spoiler!

mesaflash:

Warning: Spoiler!

meister
meister

15 Nov 2024 15:30

Replied by meister on topic LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)

LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)

Category: Computers and Hardware

Wellcome back Mecanix

there are two new cool boards:

github.com/digiexchris/rio-solidwater-shield
github.com/festlv/rioctrl-hw

and little bugfixes in the software

@all
gitano from the german forum 'https://www.cnc-aus-holz.at'has put together a cool logo

what do you think of it ?

Displaying 17341 - 17355 out of 24500 results.

Time to create page: 0.412 seconds

All Categories
LinuxCNC
- LinuxCNC Announcements
- General LinuxCNC Questions
- Installing LinuxCNC
- LinuxCNC Documents
Configuring LinuxCNC
- Configuration Tools
- - StepConf Wizard
- - PnCConf Wizard
- Basic Configuration
- Advanced Configuration
- - ClassicLadder
- - EtherCAT
- HAL
- - HAL Examples
User Interfaces
- AXIS
- Gmoccapy
- Plasmac
- pyVCP
- GladeVCP
- Other User Interfaces
- - PathPilot
- QtPyVCP
- Qtvcp
GCode and Part Programs
- G&M Codes
- O Codes (subroutines) and NGCGUI
- - Mill Library
- - Lathe Library
- - Plasma Library
- CAD CAM
- - Post Processors
- - - Fusion 360
- - - MasterCAM
- - - MecSoft
- - NativeCAM
Hardware & Machines
- Computers and Hardware
- Driver Boards
- CNC Machines
- - Milling Machines
- - Turning
- - Plasma & Laser
- Pick and Place
- Additive Manufacturing
Other Stuff
- Show Your Stuff
- Forum Questions
- User Exchange
- Off Topic and Test Posts
- - BeagleBone
International LinuxCNC Users
- Français
- Español
- Deutsch
- Other Languages
- - Russian
- - Polski