Advanced Search

vmt. Can confirm that your fixed firmware works for me and that I can compile functional f/w by making the file substitution back to wordpr.vhd.
Cheers.

I need help with this imagen, i use ubuntu 10.04, and i have 2 erros 

yes, the advantage over shiftreg is that the evaluation of e.g. encoders is already carried out on the external fpga and only the finished values are transferred

... oder über die Konfiguratoren pncconf oder mesact (github.com/jethornton/mesact) mal das Grundgerüst erstellen lassen und dann editieren.

in der ini die Karte eintragen:
[HMOT]
CARD0=hm2_7i96s.0

dann kannst in der Halshow unter:
Pins
hm1_7196s
die entsprechenden Pinnamen einsehen und ansehen/beobachten

diese kannst du dann in der Hal setzen, z.B.:
# --- Maschine on ---
net machine-is-enabled => [HMOT](CARD0).ssr.00.out-00

# --- SPINDLE-ENABLE ---
net spindle-enable => [HMOT](CARD0).ssr.00.out-01
.

Danke für das Schema, jetzt bräuchte ich noch die Einträge in der Hal

Is there a way to indicated what G_Code line you were on after an E-Stop press in QTDragon? Just goes back to 1. 

That was the fix. Thanks

Hello Tommylight, your approach is very accurate. Starting from the values ​​you propose, I was able to make relatively smooth movements. I would only highlight the need to lower the D = 0.001-0.005 a little more, since the motor emits vibration with the proposed range of values. Regards and thanks.

Post the error logs here so we can have a look.
Especially the Debug part...

Hello , Newb here. Just bought 2 , very nice Bridgeport and Jet mill retrofits , with Microkentics Steppers and PICO Universal Stepper cards , from the estate of a friend. Machines are very nicely built.
They sat idle since 2013, the Cmos batteries were dead . Ive been working on the .ini file of the Jet mill , to correct the homing sequence.
Everything was great , fixed the Z Axis homing . Powered down the control to plug the A axis in . Now on power up , it will not load Linuxcnc 2.4.5.
Is there a way to decode the error message , to see what i need to change, to return functionality ?
   The computers are bare bones machines, no network capabilities , just USB.  
             Where can I look , or were do I Start ? 

Thank you. I tried both V1.04 and V1.11.

But I couldn't make servo drive move in LinuxCNC main screen.
I didn't see any error on screen,  but servo drivers didn't become "Servo On" state when I pushed "PowerOn"

Where do I need to check ? ( I used to use another tiny LinuxCNC system and machine , but it was stepper.., I used step conf. )
Do I have to set some servo parameter from switches on servo driver ?
( No load is connected to servo motors for now. )

Servo Driver Panel shows "20ry" (2 is blinking.)


I tried both V1.11 and V1.04 and this configuration,
forum.linuxcnc.org/ethercat/52341-proble...rive?start=60#304887

I have 3 sets of Lichuan Servo (Driver+Motor), I want to use them as XYZ CNC.

I did not see any other input other than motion.probe-in, is this used for both a tool length setter and a touch probe?  My HW will support several inputs, and I would like to have each hard-wired in, without the need to swap cables, etc.

Is there a dedicated motion input for a tool length setter? If not what is the best means to have to separate HW inputs?

Thanks!!!
 

Hmmmm ... :
-walk around your area, see what businesses use CNC machines and for what and how = maintenance, service, maybe CAD/CAM and/or machine setup
-see what other businesses have offices there, what they do, drop buy any that do any manufacturing = contracting work, jobs to small for contracts are especially good as no one wants to do them
-drop buy other mom/pop shops, see if there's anything automated that can help them, or streamlining their work
-any foto/video studio, ask if they need sets/props built as needed, cam cranes or robots etc
-any food restaurants that want their logos engraved/cut/3d printed/scratched on glass = see my glass engravers here on forum, add LED's as needed
-leave your phone number to all of them
-and this is very important: do not lie to them, tell them exactly about doing market research trying to find a business that helps them but does not interfere with their existing businesses, as a rule at least 70-80% of them will really appreciate this and will gladly advise you and offer ideas.
--widen the "walk" area
-repeat above

Aaah. Awesome. Thank you. I shall try this tomorrow and see how it goes. I will let you know once I have changed the settings.