Advanced Search

Search by Keyword Keywords:

Search Options

Find Posts from

Sort Results by

Search at a specific date

Jump to Result Number

Search in Categories Also search in sub-categories

Search Results (Searched for: )

BigDo
BigDo

01 Oct 2025 12:17

Replied by BigDo on topic Nativecam running on 2.9.4 almost so close

Nativecam running on 2.9.4 almost so close

Category: NativeCAM

I completely reinstalled Linux with linuxcnc in English but the result remains the same.

ShemJ

01 Oct 2025 10:16

probe_basic nearly working but: failed to set register P0x000e to 0x0014 was created by ShemJ

probe_basic nearly working but: failed to set register P0x000e to 0x0014

Category: QtPyVCP

Hello all,

I have an ethercat setup with working axis configs and I'm trying to fire up probe basic for the first time. Everything is up to date and I've made the changes for the latest release in the ini file as well as added the new folders and files. There is some messiness in the .ini file trying to get this sorted, but I can't find anything off.

My machine will be manual tool change, no ATC for me yet, and I'm not sure I've got that right in my HAL file, especially with how it interacts with the toolchange section in probe_basic_postgui.hal. Perhaps it is this?

My error says: failed to set register P0x000e to 0x0014 and I don't know where to look to fix this issue. Can someone send me in the right direction?

Hakan
Hakan

01 Oct 2025 09:13 - 01 Oct 2025 09:16

Replied by Hakan on topic MB2hal interface to a H100 inverter

MB2hal interface to a H100 inverter

Category: Advanced Configuration

No expert by any means, but I got it to work so here are some snippets from that

in custom_sinusM.hal

# Load mb2hal for modbus operation of the sinusM vfd
loadusr -Wn sinusM mb2hal config=sinusM_spindle.ini

...

# Set max limit rpm for spindle
#
net spindle-max-freq       sinusM.05.read-max-freq.float spindlemax.max         # Max frequency(rps) for motor
net  spindle-speed-scale   spindle.0.speed-out-rps-abs   sinusM.01.set-freq     # Just the principle

net spindle-vel-positive    mux4.0.sel0           abs.spindle-speed.sign
net spindle-enable          mux4.0.sel1
net spindle-cmd-out         mux4.0.out            sinusM.04.run-command  # Stop/fwd/rev

In sinusM_spindle.ini

...

[TRANSACTION_01]
MB_TX_CODE=fnct_06_write_single_register
FIRST_ELEMENT=4
NELEMENTS=1
PIN_NAMES=set-freq
MAX_UPDATE_RATE=0.0

[TRANSACTION_04]
MB_TX_CODE=fnct_06_write_single_register
FIRST_ELEMENT=5
NELEMENTS=1
PIN_NAMES=run-command
MAX_UPDATE_RATE=0.0

[TRANSACTION_05]
MB_TX_CODE=fnct_03_read_holding_registers
FIRST_ELEMENT=41492
NELEMENTS=1
PIN_NAMES=read-max-freq
MAX_UPDATE_RATE=0.0

The above communication works with the vfd. But hal code is probably mixing Hz and rpms so it won't necessarily work for that reason.

meister
meister

01 Oct 2025 07:55

Replied by meister on topic LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)

LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5)

Category: Computers and Hardware

Mesa 7c81 over w5500 - Ethernet on RPI4 with qtdragon_hd (3.3Khz loop)

www.youtube.com/shorts/agf3f0MJxv4

BigDo
BigDo

01 Oct 2025 07:53 - 01 Oct 2025 07:55

Replied by BigDo on topic Nativecam running on 2.9.4 almost so close

Nativecam running on 2.9.4 almost so close

Category: NativeCAM

Thanks for reply. I just tried it, and the NativeCam tab remains completely empty.

meister
meister

01 Oct 2025 07:16

Replied by meister on topic Robot / coBot functions

Robot / coBot functions

Category: General LinuxCNC Questions

works for me:
www.youtube.com/shorts/Tp3savo-MGs

tommylight

30 Sep 2025 23:39

Replied by tommylight on topic Looking for a specific, detailed howto guide for XYYZ gantry setup

Looking for a specific, detailed howto guide for XYYZ gantry setup

Category: Advanced Configuration

Oh good, sorry was busy till now (1:39AM here).

tommylight

30 Sep 2025 23:37

Replied by tommylight on topic Arrow keys for jogging

Arrow keys for jogging

Category: Gmoccapy

unknown
unknown

30 Sep 2025 23:34

Replied by unknown on topic sticky estop, help needed

sticky estop, help needed

Category: Basic Configuration

I think I know what you may be trying to achieve.

If you have a look at the sample as shown in the screenshot, yes it is a pyvcp panel, it should give you the logic require if using your own panel or physical button.

jrc
jrc

30 Sep 2025 23:00

Replied by jrc on topic Leadshine 2CS3E-D507 / Cia402 almost working - help please!

Leadshine 2CS3E-D507 / Cia402 almost working - help please!

Category: EtherCAT

Many thanks! I am away today but will give it a try tomorrow and report back. I might also try making an even simpler test machine configuration with only xy coordinates, trivkins, drive by just one 2CS3E-D507 dual-stepper drive, This should hopefully be easier to debug due to having less confounding variables

scsmith1451

30 Sep 2025 22:37

Replied by scsmith1451 on topic Arrow keys for jogging

Arrow keys for jogging

Category: Gmoccapy

So sorry, I miss read the documentation, it says that the keyboard arrow keys are DISabled by default and to enable them just check the box. Where is the box? I don't see one on the screen, the settings page or anywhere else that enables the arrow keys. Can someone shed some light on where or how to enable the arrow keys?

Kind regards,

Giovanni
Giovanni

30 Sep 2025 21:29

Replied by Giovanni on topic Nativecam running on 2.9.4 almost so close

Nativecam running on 2.9.4 almost so close

Category: NativeCAM

I suppose you are using German as interface language.
Have you tried to use English?

ArcAiN6

30 Sep 2025 20:40

Replied by ArcAiN6 on topic Looking for a specific, detailed howto guide for XYYZ gantry setup

Looking for a specific, detailed howto guide for XYYZ gantry setup

Category: Advanced Configuration

Got it.. Homeing without errors, coordinate system looks correct orientation, pull off is good.
I'm happy.... now... to get all the relays and stuff going to coolant, and toolheight