1. Forum
  3. Search

Advanced Search

Search Results (Searched for: )

  • Kuzma30
  • Kuzma30
16 Sep 2025 10:49
Replied by Kuzma30 on topic 7i97T -> 7i74 -> two 7i84U (no link)

7i97T -> 7i74 -> two 7i84U (no link)

Category: Driver Boards

You are right. Problem solved when I configure board and use external 24V voltage for VIN.
  • andypugh
  • andypugh's Avatar
16 Sep 2025 09:36
Replied by andypugh on topic Touch off, OK button greyed out

Touch off, OK button greyed out

Category: AXIS

The Axis touch-off allows for any valid G-code expression, including the use of parameters. (So you should be able to type [#<_x> / 2] for example, to save typing the current X position)

Given this, "bad number format" is not a bug, but "file not found" is.

github.com/LinuxCNC/linuxcnc/issues/3563
  • MaHa
  • MaHa
16 Sep 2025 09:23 - 16 Sep 2025 11:13
FlexGui -Touch off was created by MaHa

FlexGui -Touch off

Category: Flex GUI

It seems i am attracting 'touch off' troubles. Still working on my UI. After run from terminal,homing,loading a g-code file and then press touch off button (touchoff_selected_pb) , linuxcnc shuts down with an error. At least there is some info printed in the terminal. This is from the flex_examples axis:

Warning: Spoiler!


 
  • Aciera
  • Aciera's Avatar
16 Sep 2025 09:11
Replied by Aciera on topic G81 Spindle Reversal Between Each Hole

G81 Spindle Reversal Between Each Hole

Category: General LinuxCNC Questions

If you are using peck drilling and still get strings then maybe your peck distance is not short enough?
  • NT4Boy
  • NT4Boy
16 Sep 2025 06:44
Replied by NT4Boy on topic EdgeCam Post

EdgeCam Post

Category: Post Processors

Not come across SaaSS, but will take at look at the link.

Your download links worked for me, many thanks for the pointers there.
The file opens in the Edgecam post editor so I have something to play with.
  • PCW
  • PCW's Avatar
16 Sep 2025 03:21
Replied by PCW on topic 7i76E Spindle configuration

7i76E Spindle configuration

Category: PnCConf Wizard

Can the network configuration affect?

No, the FPGA card need not even be present for pncconf to run

I would try setting the locale to en-US
  • RobotMatic
  • RobotMatic's Avatar
16 Sep 2025 01:29
Replied by RobotMatic on topic 7i76E Spindle configuration

7i76E Spindle configuration

Category: PnCConf Wizard

I can run it from the console without any problem.

Can the network configuration affect?

 
  • snowgoer540
  • snowgoer540's Avatar
16 Sep 2025 01:26 - 16 Sep 2025 01:26
Replied by snowgoer540 on topic No underspeed with temporary material

No underspeed with temporary material

Category: Plasmac

What version are you on? There were issues with adaptive feed that have been resolved.  A simple update may fix your problem.
  • langdons
  • langdons's Avatar
16 Sep 2025 00:36 - 17 Sep 2025 12:35
Replied by langdons on topic EtherCAT Isolated Digital & Analog IO Board

EtherCAT Isolated Digital & Analog IO Board

Category: Show Your Stuff

Why are the components all wonky?

(Not that I can judge, my components are 10x more wonky)
  • langdons
  • langdons's Avatar
16 Sep 2025 00:31
Replied by langdons on topic EtherCAT 32x Isolated IO + 1x 5V Differential Encoder Input

EtherCAT 32x Isolated IO + 1x 5V Differential Encoder Input

Category: Show Your Stuff

But where are the CAD files for the board?

Why does the PCB have no components on it?
  • PCW
  • PCW's Avatar
15 Sep 2025 22:58 - 15 Sep 2025 23:15
Replied by PCW on topic 7i97T -> 7i74 -> two 7i84U (no link)

7i97T -> 7i74 -> two 7i84U (no link)

Category: Driver Boards

I think I may have found the issue:

There's a bad 7i97t_7i74d.bit firmware file around

If your file is dated 2023, it's bad

The current one, fetch-able from Mesa's  web store works.
(dated May 2025)
 
  • tommylight
  • tommylight's Avatar
15 Sep 2025 20:32
Replied by tommylight on topic G81 Spindle Reversal Between Each Hole

G81 Spindle Reversal Between Each Hole

Category: General LinuxCNC Questions

Should we change the tittle to G83 ?
  • WKS-3D
  • WKS-3D's Avatar
15 Sep 2025 19:41
Replied by WKS-3D on topic Glasmaßstab EIA-422 an Mesa 7i85 (S)

Glasmaßstab EIA-422 an Mesa 7i85 (S)

Category: Deutsch

@PCW
I actually only talked about one problem, or rather, for me it was only one problem, namely that no setting leads to the index signal being recognized or responded to.
I tried changing the jumper settings to TTL signal to see if that would trigger a response, but unfortunately that wasn't the case.
For example, I went through all possible combinations from 000 to 111 to see if anything changed:

setp    hm2_7i92.0.encoder.00.index-invert 0
setp    hm2_7i92.0.encoder.00.index-mask 0
setp    hm2_7i92.0.encoder.00.index-mask-invert 0

No difference was noticeable with either the RS-422 or the TTL signal.

@tommylight
That's right, I'm not logged in as root; I just checked again, but you shouldn't do that under Linux anyway. Anyone working on the machine could destroy the entire system. Besides, everything is running smoothly except for the problem with the index, and it's not due to permissions.
I don't use a parallel port; a 7i92t + 7i76 + 7i85 is built in.

However, I have since discovered that there are often problems with the DC11 GMS and the index signal; it is either very weak or not output at all.
I probably have two such units. But since I don't want to waste any more time on this problem, I'll leave it alone and work with it as it is now.
Thank you very much for your support, and I'm glad this forum exists.

Greetings
Olli

 
  • Darium
  • Darium
15 Sep 2025 18:40
Replied by Darium on topic G81 Spindle Reversal Between Each Hole

G81 Spindle Reversal Between Each Hole

Category: General LinuxCNC Questions

@langdons
The bird nest is quite a issue,sometimes it catchs on the workpiece causing a spike on spindle load, it can even break small diameter drill. I dont think add magnet should helps since the swarf was tighten on to the drill when pulled.
Are you sure about steel wool? Mine are sharp af, got numerous cuts just to pull it out with a plier.

Standing infront of the machine for hours just to remove chips defeats the purpose of a CNC machine.i tried manually adding M4 wait for 3s then M3 it works like a charm, but also when camming a hundred holes, that shit gets old real quick.
There is no locknut in the spindle so spinning it backward shouldn't be a problem. I'mma add braking resistor to the drive so that should be fine too.
@unknow
Remaping is way way over my head and messing around with it can crash my machine (I broken a spindle shaft once, it was a sad month). I may take a look on subroutine.
i drilled some decent steel, and the chip break nicely, just that I have shit steel. Good steel is too far to get and not every part required one.
@tommylight & Aciera
It's a typo on the tittle, I always use peck drill
  • N3pu
  • N3pu
15 Sep 2025 17:13 - 15 Sep 2025 17:34
Probescreen versa v1 Problem with XYZ Auto-Zero Gmoccapy LinuxCNC 2.9.1 was created by N3pu

Probescreen versa v1 Problem with XYZ Auto-Zero Gmoccapy LinuxCNC 2.9.1

Category: General LinuxCNC Questions

Hey Guys,

I´ve bought a probe for my mill and installed the versa probescreen v1 in gmoccapy. I´ve used this source (forum.linuxcnc.org/48-gladevcp/46467-pro...-v1-for-python3-gtk3) because I´m using LinuxCNC 2.9.1. I don´t want to use v2 cause I have a lot of things programmed for the toolchange in my .hal file I don´t want to change. I just like to probe xyz and auto zero. 

After probing the probe is not at the corner of x and y and the zero point is offsettet. 
Similar issue for probing in Z direction. Zero is not set at the surface.

Is there a missunderstanding of function or is it wrong? 
I´ve uploaded a video of the issue. Maybe you´ll see something 
File Attachment:

Edit: Updated Video (cause of wrong video cut)


 
Displaying 4531 - 4545 out of 21884 results.
  1. Forum
  3. Search
Time to create page: 0.365 seconds
Powered by Kunena Forum