Advanced Search

Unfortunately, I'm still stuck, even with the additional link.
My thoughts:
Where can I get the spindle speed (float)? Would that be the value “spindle.0.speed-out,” for example, which can be seen in the attachment?
How do I transfer the float value to gladevcp.Spindel?

My favorite code doesn't work. Error "custom_postgui.hal:9: Pin 'spindle.0.speed-out' was already linked to signal 'spindle.0.speed-out'"
 

OK, I've managed to get the motor moving. The two +/- buttons now move the motor, although I'd like to have an interface with arrows. (More user-friendly)

I'm using the default LinuxCNC configuration for my 7I96S card. I need to modify the parameters for my CNC machine. How can I do this to ensure that the changes are correct?



Thank you.

Can you post the complete hal  file so that cause of the issue can be determined?

delete

Pretty sure mine does not use M68, but M67.
The included dmap2gcode can open an image and output gcode you can test with, it creates a depth map of the image so it also varies the laser PWM as needed.
You can use my config as is, but:
-you have to edit the hal file parallel port pins for your hardware
-maybe also edit the ini file velocities and accelerations for your machine as mine are set very high on acceleration and slow for velocity
-it also has a PyVCP panel that shows the PWM/laser power
-my config is alos limited to roughly 80% of max PWM to prevent pressure servo motor from triggering protection, you do not need that so you can push 100%.

With the LinuxCNC test configuration, when I select the 7I96S table option, the interface allows me to exit emergency mode. However, I cannot find a way to move the motors (there are no jogs).

For anyone else with this question, this seems to work
parent.command passes the connection to emc

Falsches Tastaturlayout, somit falsches WLAN-Passwort?

Download the archive file. I see lines there in the pwm part -
loadrt pwmgen output_type=1
addf pwmgen.make-pulses base-thread 
addf pwmgen.update servo-thread
net pwmdhez motion.teleop-mode => not.0.in
setp pwmgen.0.pwm-freq 1000.0
setp pwmgen.0.scale 6.0
setp pwmgen.0.offset 0.1

specific, not for me -

setp pwmgen.0.dither-pwm true
net jasht logic.0.and pwmgen.0.enable
net dout-00 <= pwmgen.0.pwm
net dout-00 => parport.0.pin-02-out

Doesn't work. I checked the electrician. With command M68 E0 Q 0.0 voltage per pin 14 = -0.4v, M68 E0 Q 1 voltage 4.7. I won't tell you the frequency.

1. you are selecting stuff you do not need, like parallel port
2. might also be the "locale" thing where the wizard has issues with other languages than English.
To test, boot the PC from the USB you used to install LinuxCNC in LIVE mode, use the wizard to make a new configuration and save it to hard drive or another USB, then reboot to normal install and test the config.

Open the hal file attached at that link, somewhere lower in the thread, it is named Graveri kuq as zip file, compare your hal to mine till you get it working, then add the safety stuff with some signal names in Albanian.

Would it be possible to download the INI and HAL files for my Mesa and LinuxCNC version?

I have made many configurations and I still cannot control the machine.

I’m on that topic (at the same time I express my admiration for the design shown there) but I didn’t see anything on my question. 
Clearly I'm doing something wrong in the hal file.

But what exactly?

Have a look at this, there is also the complete config attached there, it is the same thing as laser as it uses PWM to control the grinding bit pressure, and it also should have provisions for turning off the laser when canceling or pausing or stopping a job, that is normally not done with normal configs.
forum.linuxcnc.org/show-your-stuff/46752...er-scratcher?start=0

        ​Hello everyone,​I'm working on repairing a Yaskawa CACR-SR20BE12G-E servo drive. I initially had to replace all the capacitors as two of them had incorrect values, which was causing the A.02 error. After installing the board, everything worked fine for about 30 minutes, but then the auxiliary power supply errors A.03 and A.40 appeared.​I've isolated the critical components after the transformer T3076, specifically D20 (code C3) and AVR4 (code 8C E4), which now appear to be faulty.​I need help confirming the identity and replacement parts for these components.​1. D20 (Code C3) - Raddrizzatore Schottky​I have traced the pinout of D20 and have the following connections:​CENTER PIN: Connects to the positive pole of capacitor C41 33uf 25v​TOP LEFT PIN: Connects to the transformer output, passing through diode D32.​RIGHT PIN: Goes to the negative side of the board (or where the letter 'N' is marked).​Question: Can anyone who has successfully repaired this confirm if the correct replacement is indeed the BAT54C (Dual Common Cathode, SOT-23)?​2. AVR4 (Code 8C E4) -​dimension(approx. 3x2mm). The marking on my faulty board is 8C E4, while a known working board shows 8C E8 (I assume the last digit is just a batch code).​Pinout/Measurements:​I'm using the following numbering: Pin 1 (Top Left), Pin 2 (Center), Pin 3 (Top Right), and Pin 4 (Bottom). Note that Pin 4 is common with Pin 2 on the board.​Using the diode function on my multimeter:​Black probe on Pin 2 or 4, Red probe on Pin 1 or 3 Reads 2.3v- 2.4V​Inverting the probes Reads 0.5 - 0.6V

Can you help me please?