Plasmac 758 topics

A place to ask questions about the Plasmac interface

Subject	Replies / Views	Last Post
QTPlasmaC mode2 - valid arc lost Category: Plasmac Topic started 5 years 1 month ago, by fernandosf Last Post 5 years 1 month ago by fernandosf 1 2	Replies:19 Views:3550	Last Post by fernandosf 5 years 1 month ago
THCAD-10 and voltaje divider ratio. Category: Plasmac Topic started 5 years 2 months ago, by paulsao Last Post 5 years 1 month ago by rodw	Replies:8 Views:2050	Last Post by rodw 5 years 1 month ago
Choosing a compressor for plasma cutting Category: Plasmac Topic started 6 years 1 month ago, by tommylight Last Post 5 years 1 month ago by billykid 1 2	Replies:12 Views:9207	Last Post by billykid 5 years 1 month ago
QtPlasmaC Jogging Lag Category: Plasmac Topic started 5 years 1 month ago, by Uthayne Last Post 5 years 1 month ago by Uthayne 1 2 3 4	Replies:32 Views:5287	Last Post by Uthayne 5 years 1 month ago
PlasmaC Will Not Activate Torch Pin on My 7i96 Category: Plasmac Topic started 7 years 1 month ago, by MakingStuff Last Post 5 years 1 month ago by pkasy 1 2 3	Replies:25 Views:4922	Last Post by pkasy 5 years 1 month ago
QTvcp ERROR! Message # 1 Category: Plasmac Topic started 5 years 1 month ago, by danilom Last Post 5 years 1 month ago by phillc54	Replies:1 Views:1188	Last Post by phillc54 5 years 1 month ago
Which THCAD to use for Plasma cutter without voltage divider Category: Plasmac Topic started 5 years 4 months ago, by alchemy Last Post 5 years 2 months ago by tommylight 1 2	Replies:12 Views:4457	Last Post by tommylight 5 years 2 months ago
wrong scale thc of the z axis during cutting on qtplasmac Category: Plasmac Topic started 5 years 3 months ago, by sibista Last Post 5 years 2 months ago by sibista 1 2 3 ... 10	Replies:94 Views:14.2k	Last Post by sibista 5 years 2 months ago
QTPlasmaC, first cut ever. What to do after "initial setup"? Category: Plasmac Topic started 5 years 2 months ago, by fernandosf Last Post 5 years 2 months ago by phillc54 1 2 3	Replies:20 Views:5749	Last Post by phillc54 5 years 2 months ago
Fusión 360 and Plasmac Category: Plasmac Topic started 5 years 2 months ago, by paulsao Last Post 5 years 2 months ago by paulsao	Replies:7 Views:1349	Last Post by paulsao 5 years 2 months ago
IMPORTANT NOTICE for PlasmaC users Category: Plasmac Topic started 5 years 5 months ago, by phillc54 Last Post 5 years 2 months ago by phillc54	Replies:1 Views:9054	Last Post by phillc54 5 years 2 months ago
Showing G53 coordinates Category: Plasmac Topic started 5 years 2 months ago, by fernandosf Last Post 5 years 2 months ago by beefy 1 2 3	Replies:21 Views:5050	Last Post by beefy 5 years 2 months ago
Ignore probe during cut Category: Plasmac Topic started 5 years 2 months ago, by mariusl Last Post 5 years 2 months ago by mariusl	Replies:8 Views:2193	Last Post by mariusl 5 years 2 months ago
PnCConf Wizard doesn't launch Category: Plasmac Topic started 5 years 2 months ago, by CFE Last Post 5 years 2 months ago by crowloy 1 2	Replies:19 Views:3184	Last Post by crowloy 5 years 2 months ago
QTPlasmaC Z axis "following error" (but it works in AXIS) Category: Plasmac Topic started 5 years 2 months ago, by fernandosf Last Post 5 years 2 months ago by fernandosf	Replies:7 Views:1588	Last Post by fernandosf 5 years 2 months ago
Camera For Touchoff Category: Plasmac Topic started 6 years 1 month ago, by phillc54 Last Post 5 years 2 months ago by partec 1 2 3 ... 7	Replies:60 Views:17k	Last Post by partec 5 years 2 months ago
ohm sensor Category: Plasmac Topic started 5 years 2 months ago, by chuben Last Post 5 years 2 months ago by chuben	Replies:2 Views:1128	Last Post by chuben 5 years 2 months ago
qtplasmac error message Category: Plasmac Topic started 5 years 2 months ago, by crowloy Last Post 5 years 2 months ago by phillc54	Replies:6 Views:1377	Last Post by phillc54 5 years 2 months ago
QTPlasmc GUI questions Category: Plasmac Topic started 5 years 2 months ago, by robertspark Last Post 5 years 2 months ago by cmorley	Replies:6 Views:1273	Last Post by cmorley 5 years 2 months ago
QTPlasmac and estop-latch broken (no iocontrol.0.user-request-enable) Category: Plasmac Topic started 5 years 3 months ago, by rodw Last Post 5 years 3 months ago by cmorley 1 2 3	Replies:20 Views:5093	Last Post by cmorley 5 years 3 months ago

Time to create page: 0.043 seconds