Advanced Search

Where did you place the file?

Did you install Mesa CT?

JT

If not using the Flexi-HAL board, I'd recommend to use the standard remora-spi component. First step is to get a basic 3 axis configuration up and running and then add in the additional axes.

There are various config examples here:
github.com/scottalford75/Remora/tree/mai...nuxCNC/ConfigSamples

dont use the flexihal configs for this, download the sample configurations from the remora github and try with those

I think I misread that first error,
remove the xhc-whb04b-6.hal

Hi,
I'm using linuxcnc since a while. I upgraded a few weeks ago: Now I'm using a Rpi and a MESA 7C81. I'm having 3 axis and a fixed vertical spindle motor and a separated a-axis. All 4 axes are running with stepper motors.

I'm using inventor-hsm for creating G-code which works pretty good. Unfortunately, it is very limited, when using it in connection with the A-axis. Although the software is able to unwrap a geometry I can only run it to mill out closed pocked (also when it is wrapped). Very frequently I need to reduce a diameter and there is no operation available for this. I can only do this in indexed mode (several phi-angles and slicing in z). 

Luckily the software can also produce code for turning machines, so I could create code for such a machine. The only thing I need to do is to turn on a horizontal spindle, you see my idea?

So my question: 
Is there a possibility to configure linuxcnc in such a way that I can use my A-stepper axis for running as horizontal spindle?

What I need is a G-command turning the horizontal spindle on in a certain speed and a G-command for turning it of, during the turn-on the stepper needs to run continuously. I know its a bit absurd

Georg  

Thanks!

I took a stab at making a hal component but was having issues getting it to compile with comp. Seems like comp isnt installed ("which comp" returns nothing) running the 2.9.3 iso. I also tried installing from git but was having the same issue. Anything special that needs to be done?

Was able to get it working by directly controlling the pins on the 7i96s with a custom M code for now but would like to get it going with a custom hal component.


 

oh mein fehler, wenn man den Wald vor lauter Bäumen nicht mehr sieht
dank dir! Was muss ich in der Endstufe für Parameter ändern das diese mit dem Master kommuniziert?
 

I installed the nvmpg component but I still have the same error with the command
sudo halcompile --install nvmpg.c.

I have a Linux Mint LMDE 6 Faye version, it may be too old?
 

I'm trying to put LinuxCNC on Mint 22.1. I followed Beef's directions here:
iamtherealbeef.com/content/linuxcnc-on-linuxmint-22/
It all went great (much thanks), but I have an error when I run linuxcnc. Debug file info:
Missing rtapi.conf. Check your installation.
49550

Help will be greatly appreciated!
Steve

So i've been tinkering a little and getting to learn the new enviroment.I have made my basic configuration of a .HAL file for linuxCNC, don't mind that the I/O pins are not defined correct in relation to my hardware.When defining the outputs i stumpled upon the .CFG file that defines for example RS-485 spindle control over modbus.I have linked the 2 files as .txt could anyone please give feedback and advice.TIA.

So how would I create a pin?

Pins are created by hal components.

in the line above 'dout-01' is a signal name
'hm2_7i96s.0.ssr.00.out-01' is a pin name

hence you get an error using the 'setp' command on the signal name
Try using (note sets instead of setp)

Danke für den Hinweis. leider ohne Erfolg

Hi all,

I’m quite new here and still have a lot to learn, thanks all for your patience. I have been trying my best to get good print results with an Ender3 with a 100mm round build plate on two rotational axes. I wrote a blender addon that does ‘indexed’ 5 axis printing.
My setup with the pi 5 and gpio was not a suitable solution. I am hoping to get my octopus v1.1 working with remora. 

1) I successfully flashed the mcu
2) my wiring is correct
3) I get no read response from spi connection
4) when I start Linux cnc with my config, it says that joint.5.scale is not found ( extruder)

I will attach my hal and ini files in a bit. 

Thanks again, im reading away. Also I did know that RPI needs the parallel hat by byte to bot. When looking at the hal file form them it doesn't show the GPIO code in it like yours does thanks again.