1. Forum
  3. Search

Advanced Search

Search Results (Searched for: )

  • Marko6
  • Marko6
11 Oct 2025 14:00
Replied by Marko6 on topic Ethercat, EL6751 and CANOpen

Ethercat, EL6751 and CANOpen

Category: EtherCAT

Thanks for a help, I am not big pro in Linuxcnc. 

Spindle.0 is Delta C2000 and ethercat card running in Velocity mode. So I made comp file that sending enable signal to it and the rest is usuall cia402.

Spindle.1 is SD2S via CoE. 

If I have just one spindle.0 its running well. Then if I add spindle.1 it runs well but spindle.0 receive just setpoint without enable word.
 
  • endian
  • endian's Avatar
11 Oct 2025 12:07
Replied by endian on topic Ethercat, EL6751 and CANOpen

Ethercat, EL6751 and CANOpen

Category: EtherCAT

Thanks. It works now.

However I have spindle.0 and spindle.1 and as soon as I added spindle.1, spindle0 stopped working (Linuxcnc - Qtdragon only sends the setpoint.0 value and no enable signal). Strange.
 

Upload your config ... I can check it.. more detail as ..

 
  • Marko6
  • Marko6
11 Oct 2025 10:24
Replied by Marko6 on topic Ethercat, EL6751 and CANOpen

Ethercat, EL6751 and CANOpen

Category: EtherCAT

Thanks. It works now.

However I have spindle.0 and spindle.1 and as soon as I added spindle.1, spindle0 stopped working (Linuxcnc - Qtdragon only sends the setpoint.0 value and no enable signal). Strange.
  • besriworld
  • besriworld
11 Oct 2025 10:09 - 28 Jan 2026 12:33
Replied by besriworld on topic OLD Lathe conversion to a CNC

OLD Lathe conversion to a CNC

Category: Turning

After replacing the processor there are no warning messages or the machine stops.

I made a new video a little long but it is a compilation of all the operations. The hydraulic chuck are missing :side:



PS:


Hello,
I had a rough week with my small lathe. After the workpiece slipped out of the jaws, the X-axis went out of alignment and had to be realigned. Luckily, that was the only damage. ?

 
 
 
 
 
  • ChrisB_II
  • ChrisB_II's Avatar
11 Oct 2025 10:07
Replied by ChrisB_II on topic Axis configuration not fully working on 2.9.6

Axis configuration not fully working on 2.9.6

Category: AXIS

I hope it is understandable - my english is way too rusty to explain such a problem ;-)

github.com/LinuxCNC/linuxcnc/issues/3583
  • Aciera
  • Aciera's Avatar
11 Oct 2025 10:03
Replied by Aciera on topic Gmoccapy tool setter install "errors"

Gmoccapy tool setter install "errors"

Category: Gmoccapy

This is from your 'gmoccapy_postgui.hal':
...
net tool-change-request    => gmoccapy.toolchange-change
net tool-change-confirmed  <= gmoccapy.toolchange-changed
net tool-number            => gmoccapy.toolchange-number
.
.
.
net tool-change gmoccapy.toolchange-change <= iocontrol.0.tool-change
net tool-changed gmoccapy.toolchange-changed => iocontrol.0.tool-changed
net tool-prep-number gmoccapy.toolchange-number <= iocontrol.0.tool-prep-number
...

As has already been stated, you cannot reuse the same halpins use the signals they were assigned to.
Maybe this helps to explain some of the basics:
linuxcnc.org/docs/html/hal/intro.html
  • unknown
  • unknown
11 Oct 2025 09:42 - 11 Oct 2025 09:47
Replied by unknown on topic Strugling with installation

Strugling with installation

Category: Installing LinuxCNC

Yeah Rod reckons it's a Debian issue.

Rods take on it
forum.linuxcnc.org/9-installing-linuxcnc...amd64-version#332160

Every time a user is hit by the issue they start a new thread, I've tried to start a sticky, but as usual search doesn't get used, so it's a page or 2 walking a user through it.

But yeah it does appear to be frustrating. Maybe it requires pulling apart the squashfs file that the installer uses and manipulating that. I dunno just talking to myself.
  • andypugh
  • andypugh's Avatar
11 Oct 2025 09:36
Replied by andypugh on topic Strugling with installation

Strugling with installation

Category: Installing LinuxCNC

Not my mess, luckily, but i hate dealing with it as it's been dragging for over a year now, all because someone did not clean the build environment before building the ISO.

Can you explain to me exactly what the problem is? I have not been able to keep up with the forum for quite some time. 

I was aware that there was an issue of some sort, but though that it was in upstream Debian? 
  • Dragan
  • Dragan
11 Oct 2025 08:52
Replied by Dragan on topic NEW BUILD, need help with e-stop in tklinuxcnc

NEW BUILD, need help with e-stop in tklinuxcnc

Category: Basic Configuration

Hello friends, thanks to everyone for the help. Unfortunately, it didn't work out, and after two days, I gave up and looked for another solution. I stumbled across an Arduino in my boxes and decided to go with UGS on Raspberry (VNC) & GRBL on Arduino. Everything worked flawlessly right away. I'm satisfied. Thanks again to all and best wishes.

Thanks,
Dragan
  • Aciera
  • Aciera's Avatar
11 Oct 2025 07:34
Replied by Aciera on topic rotary axis brakes

rotary axis brakes

Category: Advanced Configuration

I'm sorry but I cannot read anything on that screen shot with the error but maybe this example ini helps:
github.com/LinuxCNC/linuxcnc/blob/master...ng_indexer/xyyzb.ini
  • Hakan
  • Hakan
11 Oct 2025 07:34 - 11 Oct 2025 07:35
Replied by Hakan on topic Ethercat drives not responding, mesa error finishing read

Ethercat drives not responding, mesa error finishing read

Category: EtherCAT

Since you have problems with the Realtek adapters, here is a tip.
Add an Intel PCIe network adapter. Of course you need a free PCIe slot. With an X4 slot you can use a board with multiple interfaces.
And if you only have an M.2 slot you can use that forum.linuxcnc.org/18-computer/55782-adding-a-m-2-ethernet-port
 
  • Aciera
  • Aciera's Avatar
11 Oct 2025 07:29
Replied by Aciera on topic Button on Linuxcnc interface that switches an output on Mesa 7i76e on and off

Button on Linuxcnc interface that switches an output on Mesa 7i76e on and off

Category: GladeVCP

You don't need a handler for what you want.

Here is an example that creates a led connected to 'halui.machine.is-on' and a button connected to 'halui.machine.on'  

 

File Attachment:

File Name: example.ui
File Size:2 KB


 

File Attachment:

File Name: example_postgui.hal
File Size:0 KB
  • jefsaro
  • jefsaro's Avatar
11 Oct 2025 07:15
Replied by jefsaro on topic rotary axis brakes

rotary axis brakes

Category: Advanced Configuration

par contre , j 'ai changer les ligne de [axis_a] a [joint3]  et linux demarre sans erreur ,mais le frein ne fonctionne pas , une idee?
  • jefsaro
  • jefsaro's Avatar
11 Oct 2025 07:13
Replied by jefsaro on topic rotary axis brakes

rotary axis brakes

Category: Advanced Configuration

merci pour la reponse , quand je retire emcmot , j 'ai cette erreur.
  • unknown
  • unknown
11 Oct 2025 04:42
Replied by unknown on topic fixing "raspi firmware" errors on the official amd64 ISO

fixing "raspi firmware" errors on the official amd64 ISO

Category: Installing LinuxCNC

A small shell script
download the file and open the directory (containing the file)in a terminal 

File Attachment:

File Name: amd64-rpi-...-fix.txt
File Size:0 KB

cp amd64-rpi-firmware-fix.txt amd64-rpi-firmware-fix.sh
chmod x amd64-rpi-firmware-fix.sh
./amd64-rpi-firmware-fix.sh

You can delete the files when done.
Displaying 9226 - 9240 out of 16368 results.
  1. Forum
  3. Search
Time to create page: 0.635 seconds
Powered by Kunena Forum