StepConf Wizard 594 topics

Stepper Configuration Wizard for Parallel Port

Forum Header

Subject	Replies / Views	Last Post
1st time stpconf setup Topic started 18 Mar 2013 12:31, by happytriger2000 Last Post 19 Mar 2013 08:31 by happytriger2000	Replies:4 Views:2507	happytriger2000 Last Post by happytriger2000 19 Mar 2013 08:31
Unexpected waveform results Topic started 08 Mar 2013 03:01, by CinciJeff Last Post 15 Mar 2013 14:27 by rip1980 1 2	Replies:11 Views:9874	rip1980 Last Post by rip1980 15 Mar 2013 14:27
Roland EGX 600 Stepconfigs Topic started 28 Feb 2013 19:03, by album.digital.ficheiros Last Post 28 Feb 2013 23:37 by andypugh	Replies:3 Views:2899	Last Post by andypugh 28 Feb 2013 23:37
Learnware Okto Bus Topic started 25 Feb 2013 22:15, by hudsonvx Last Post 25 Feb 2013 23:08 by PCW	Replies:1 Views:2591	Last Post by PCW 25 Feb 2013 23:08
Stepconf test axis problem Topic started 24 Feb 2013 04:15, by johnybg Last Post 24 Feb 2013 15:29 by johnybg	Replies:2 Views:3038	johnybg Last Post by johnybg 24 Feb 2013 15:29
BROKEN PIPE REPOON SETUP WHEN TRYING TO JOG MOTORS Topic started 09 Mar 2011 19:20, by naps Last Post 23 Feb 2013 06:36 by keithcat	Replies:9 Views:15.1k	keithcat Last Post by keithcat 23 Feb 2013 06:36
need help configuring LinuxCNC Topic started 15 Feb 2013 08:25, by rebeltaz Last Post 16 Feb 2013 02:58 by rebeltaz	Replies:7 Views:4569	rebeltaz Last Post by rebeltaz 16 Feb 2013 02:58
TB6560: "Digital out 0" vs "Amplifier Enable X"? Topic started 15 Jan 2013 00:13, by awes Last Post 11 Feb 2013 22:25 by BigJohnT	Replies:8 Views:6709	Last Post by BigJohnT 11 Feb 2013 22:25
Errors with Xylotek controller Topic started 22 Oct 2012 03:31, by Sterling Last Post 27 Jan 2013 09:26 by Sterling 1 2	Replies:17 Views:13.9k	Last Post by Sterling 27 Jan 2013 09:26
Two different step drivers? Topic started 20 Jan 2013 07:47, by jaredts Last Post 20 Jan 2013 17:10 by cncbasher	Replies:1 Views:3146	cncbasher Last Post by cncbasher 20 Jan 2013 17:10
Axis runs 5 times farther Topic started 18 Jan 2013 17:38, by belegnar Last Post 18 Jan 2013 18:44 by cncbasher	Replies:1 Views:3167	cncbasher Last Post by cncbasher 18 Jan 2013 18:44
different max speed for rapid and feed movement? Topic started 11 Nov 2012 21:19, by helig Last Post 18 Nov 2012 01:37 by helig	Replies:6 Views:7246	helig Last Post by helig 18 Nov 2012 01:37
parallel port settings for Probotix meteor Topic started 16 Nov 2012 01:06, by rmattioda Last Post 16 Nov 2012 08:55 by BigJohnT	Replies:1 Views:3220	Last Post by BigJohnT 16 Nov 2012 08:55
Setting for Gecko 210X Topic started 02 Sep 2012 15:00, by Rick4004 Last Post 04 Sep 2012 12:05 by andypugh	Replies:6 Views:9298	Last Post by andypugh 04 Sep 2012 12:05
2 Parport with step config Topic started 07 Aug 2012 08:46, by marcguenel Last Post 07 Aug 2012 16:06 by BigJohnT	Replies:6 Views:10.2k	Last Post by BigJohnT 07 Aug 2012 16:06
How can I setup dual X motors in stepconf? Topic started 28 Jul 2012 13:31, by CptanPanic Last Post 29 Jul 2012 09:47 by Rick G	Replies:3 Views:8500	Last Post by Rick G 29 Jul 2012 09:47
Need Help Topic started 21 Jun 2012 17:19, by ricky_a Last Post 14 Jul 2012 22:08 by ricky_a 1 2 3 ... 6	Replies:51 Views:32.9k	ricky_a Last Post by ricky_a 14 Jul 2012 22:08
Syil stepper drivers Topic started 03 Jul 2012 22:47, by tactustech Last Post 10 Jul 2012 11:51 by BigJohnT 1 2	Replies:16 Views:16.7k	Last Post by BigJohnT 10 Jul 2012 11:51
emc2 don't start .... Topic started 11 Aug 2011 15:08, by thor1966 Last Post 01 Jul 2012 16:21 by jy76	Replies:9 Views:13.9k	jy76 Last Post by jy76 01 Jul 2012 16:21
Motors never reverse Topic started 06 Jun 2012 19:48, by jblain Last Post 14 Jun 2012 19:08 by jblain 1 2 3	Replies:25 Views:23.9k	jblain Last Post by jblain 14 Jun 2012 19:08

Time to create page: 0.129 seconds