Basic Configuration 1226 topics

A place to discuss basic configurations like probe input, homing etc.

Subject	Replies / Views	Last Post
How do I zero an axis when homed? Topic started 03 Oct 2020 15:06, by jhandel Last Post 05 Oct 2020 00:56 by jhandel 1 2	Replies:15 Views:4105	jhandel Last Post by jhandel 05 Oct 2020 00:56
Adding a second Y axis homing switch on a parallel port setup Topic started 27 Sep 2020 20:11, by DaveInConesus Last Post 04 Oct 2020 16:52 by tommylight	Replies:1 Views:644	Last Post by tommylight 04 Oct 2020 16:52
MESA 7I76e configuration - X-Axis travel overshoot Topic started 29 Sep 2020 13:32, by Xpertmill Last Post 01 Oct 2020 17:12 by Xpertmill	Replies:6 Views:883	Xpertmill Last Post by Xpertmill 01 Oct 2020 17:12
XY Zero not aligned Topic started 26 Sep 2020 08:22, by Jocman Last Post 28 Sep 2020 16:16 by Jocman	Replies:1 Views:731	Jocman Last Post by Jocman 28 Sep 2020 16:16
Why does fractional SCALE cause linuxcnc to complain about a version update? Topic started 27 Sep 2020 02:30, by JetForMe Last Post 27 Sep 2020 14:02 by PCW	Replies:5 Views:668	Last Post by PCW 27 Sep 2020 14:02
Adding 4th axis to my gantry machine, getting "Following Error" Topic started 26 Sep 2020 09:06, by JetForMe Last Post 27 Sep 2020 01:43 by JetForMe	Replies:2 Views:618	Last Post by JetForMe 27 Sep 2020 01:43
Configuring a Floating Head Topic started 12 Sep 2020 17:51, by Aldenflorio Last Post 21 Sep 2020 21:41 by Aldenflorio 1 2 3 ... 11	Replies:104 Views:9039	Last Post by Aldenflorio 21 Sep 2020 21:41
Setting up Mesa 7i76e - issues Topic started 14 Sep 2020 08:33, by Jocman Last Post 18 Sep 2020 16:24 by Jocman	Replies:8 Views:1116	Jocman Last Post by Jocman 18 Sep 2020 16:24
Spindle Control with Huanyang VFD Using RS485 Topic started 14 Sep 2020 19:53, by Doogood Last Post 16 Sep 2020 15:28 by slc	Replies:2 Views:5328	slc Last Post by slc 16 Sep 2020 15:28
Control spindle with g code Topic started 11 Sep 2020 21:49, by rotccapt Last Post 11 Sep 2020 22:20 by cmorley	Replies:5 Views:1224	cmorley Last Post by cmorley 11 Sep 2020 22:20
mux 4 not recognized Topic started 08 Sep 2020 16:37, by jpg Last Post 09 Sep 2020 07:40 by Mike_Eitel	Replies:7 Views:975	Last Post by Mike_Eitel 09 Sep 2020 07:40
Z axis cuts in the air - SOLUTION Topic started 08 Sep 2020 07:50, by Jeff65 Last Post 08 Sep 2020 12:20 by Aciera	Replies:1 Views:630	Last Post by Aciera 08 Sep 2020 12:20
LinuxCNC trips on M6 Topic started 01 Sep 2020 02:35, by underscore Last Post 06 Sep 2020 16:38 by underscore	Replies:7 Views:996	Last Post by underscore 06 Sep 2020 16:38
Z axis cuts in the air - not plunging Topic started 05 Sep 2020 10:58, by Jeff65 Last Post 06 Sep 2020 11:13 by Clive S 1 2 3 ... 6	Replies:59 Views:4784	Clive S Last Post by Clive S 06 Sep 2020 11:13
Tandem Axis with one Home/Limit switch Topic started 03 Sep 2020 23:54, by palador Last Post 04 Sep 2020 11:03 by palador	Replies:2 Views:1416	palador Last Post by palador 04 Sep 2020 11:03
Chinese 3040Z-DQ parallel port CNC router Config troubles Topic started 29 Aug 2020 03:28, by gfiber Last Post 31 Aug 2020 23:11 by gfiber	Replies:2 Views:1357	gfiber Last Post by gfiber 31 Aug 2020 23:11
Working with mesa 7i76e Topic started 28 Aug 2020 16:05, by Jocman Last Post 30 Aug 2020 09:30 by Jocman	Replies:2 Views:1101	Jocman Last Post by Jocman 30 Aug 2020 09:30
Tool table offsets, Z axis limit exceeded with G43, but program runs ok Topic started 27 Aug 2020 23:54, by kapucin Last Post 28 Aug 2020 15:54 by kapucin	Replies:1 Views:877	kapucin Last Post by kapucin 28 Aug 2020 15:54
Initial Coordinates Topic started 23 Aug 2020 18:20, by AgentWD40 Last Post 26 Aug 2020 14:15 by AgentWD40	Replies:4 Views:782	Last Post by AgentWD40 26 Aug 2020 14:15
Deactivate or increase the soft limit Topic started 22 Aug 2020 11:47, by cyberspaceschwabe Last Post 22 Aug 2020 20:42 by tommylight	Replies:5 Views:800	Last Post by tommylight 22 Aug 2020 20:42

Time to create page: 0.193 seconds