General LinuxCNC Questions 5977 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
Latency, error finishing read, and IRQ affinity Topic started 10 Feb 2024 02:51, by mozmck Last Post 17 Nov 2025 02:23 by BryceJ 1 2 3 ... 7	Replies:62 Views:32.9k	Last Post by BryceJ 17 Nov 2025 02:23
Index to Linuxcnc & the Raspberry Pi (4 & 5) Official Images Only!!! Topic started 26 Mar 2025 22:07, by unknown Last Post 27 Mar 2025 00:48 by tommylight	Replies:4 Views:10.2k	Last Post by tommylight 27 Mar 2025 00:48
Position Logger Topic started 21 Feb 2021 14:44, by BigJohnT Last Post 16 Dec 2024 18:24 by JT	Replies:8 Views:13.7k	Last Post by JT 16 Dec 2024 18:24
Other Sources for Information about LinuxCNC Topic started 08 Jan 2013 02:16, by BigJohnT Locked Last Post 08 Jan 2013 02:16 by BigJohnT Locked	Replies:0 Views:17.2k	Last Post by BigJohnT 08 Jan 2013 02:16
FAQ Topic started 17 Feb 2010 13:25, by BigJohnT Locked Last Post 17 Feb 2010 13:25 by BigJohnT Locked	Replies:0 Views:21.6k	Last Post by BigJohnT 17 Feb 2010 13:25

Probe tripped during non-probe move deadlock Topic started 26 Jul 2025 03:30, by AkkiSan Last Post 08 Dec 2025 13:00 by tommylight 1 2 3	Replies:26 Views:1964	Last Post by tommylight 08 Dec 2025 13:00
Hybrid Manual/Stepper Control Topic started 04 Dec 2025 10:41, by voltaicsca Last Post 08 Dec 2025 11:14 by tommylight	Replies:5 Views:219	Last Post by tommylight 08 Dec 2025 11:14
wait_complete() Topic started 30 Aug 2021 12:27, by RKtech Last Post 07 Dec 2025 23:32 by jcdammeyer	Replies:5 Views:1305	Last Post by jcdammeyer 07 Dec 2025 23:32
Bimanual Operation (Paused/Resume) in Homing Process Topic started 07 Dec 2025 22:02, by rbobey1989 Last Post 07 Dec 2025 22:21 by rbobey1989	Replies:1 Views:62	Last Post by rbobey1989 07 Dec 2025 22:21
Linuxcnc Image for Raspberry Pi 3 Topic started 29 Nov 2021 17:24, by tsewell Last Post 04 Dec 2025 07:16 by masawee 1 2	Replies:12 Views:8651	masawee Last Post by masawee 04 Dec 2025 07:16
Remora (SKR 1.4 RPi) – massive SPI noise, “bad payload” communication fails Topic started 01 Dec 2025 19:21, by Chad Last Post 02 Dec 2025 15:34 by Chad	Replies:5 Views:215	Chad Last Post by Chad 02 Dec 2025 15:34
Issue with G38.5 Topic started 20 Oct 2025 17:21, by christer Last Post 01 Dec 2025 11:49 by abs32 1 2	Replies:10 Views:1011	abs32 Last Post by abs32 01 Dec 2025 11:49
Is the wiki down? Topic started 01 Dec 2025 03:31, by tdonia Last Post 01 Dec 2025 11:21 by unknown	Replies:2 Views:140	unknown Last Post by unknown 01 Dec 2025 11:21
The Current Bread & Butter Setup? Topic started 30 Nov 2025 17:13, by Billy Boy Last Post 01 Dec 2025 10:44 by unknown 1 2	Replies:10 Views:386	unknown Last Post by unknown 01 Dec 2025 10:44
Problem with linear movement Topic started 30 Nov 2025 20:17, by MaHa Last Post 01 Dec 2025 07:28 by MaHa	Replies:2 Views:149	MaHa Last Post by MaHa 01 Dec 2025 07:28
Is there any way to use Pncconf Wizard to set up 7i97T with 7i73 pendant board? Topic started 29 Nov 2025 14:11, by Tinker Last Post 29 Nov 2025 21:12 by rodw	Replies:4 Views:180	Last Post by rodw 29 Nov 2025 21:12
carousel.comp scale questions. Topic started 23 Nov 2025 08:18, by rasmus Last Post 29 Nov 2025 20:27 by rasmus	Replies:4 Views:281	rasmus Last Post by rasmus 29 Nov 2025 20:27
LinuxCNC 2.9.3 .xz image for RPi 5 is not available in the ISO directory Topic started 19 Nov 2025 04:40, by 4ashishkr Last Post 28 Nov 2025 21:41 by andypugh	Replies:4 Views:255	Last Post by andypugh 28 Nov 2025 21:41
EtherCAT + CiA402 Servo: OP state reached, but axis won’t move (only Following E Topic started 15 Nov 2025 22:52, by aDm1N Last Post 28 Nov 2025 21:33 by aDm1N 1 2	Replies:11 Views:862	Last Post by aDm1N 28 Nov 2025 21:33
Is something up with 2.9.7 (joint errors) Topic started 21 Nov 2025 19:17, by 1911ut Last Post 28 Nov 2025 20:33 by andypugh	Replies:4 Views:287	Last Post by andypugh 28 Nov 2025 20:33

Time to create page: 0.712 seconds