General LinuxCNC Questions 6114 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
laser point cloud scanner? Topic started 03 Apr 2022 12:06, by robertspark Last Post 06 Apr 2022 09:35 by robertspark	Replies:4 Views:1196	robertspark Last Post by robertspark 06 Apr 2022 09:35
Adding Rotary Axis to CNC Router - Sanity Check Required. Topic started 03 Apr 2022 10:04, by Skippy1 Last Post 05 Apr 2022 00:09 by Skippy1	Replies:3 Views:891	Last Post by Skippy1 05 Apr 2022 00:09
Post-processor for Rhino Grasshopper Topic started 21 Mar 2022 15:10, by aaron Last Post 04 Apr 2022 08:15 by aaron	Replies:9 Views:1366	aaron Last Post by aaron 04 Apr 2022 08:15
Lincurve Topic started 11 Mar 2022 15:59, by rider-83 Last Post 02 Apr 2022 14:52 by rider-83 1 2	Replies:11 Views:3942	rider-83 Last Post by rider-83 02 Apr 2022 14:52
Stepper motor motion Topic started 01 Apr 2022 14:55, by Slippery Last Post 01 Apr 2022 16:54 by tommylight	Replies:1 Views:753	Last Post by tommylight 01 Apr 2022 16:54
Strange tool paths Topic started 31 Mar 2022 13:09, by Tintin Last Post 01 Apr 2022 07:43 by Tintin	Replies:8 Views:1269	Last Post by Tintin 01 Apr 2022 07:43
Gantry homing move in same direction when siwtch is hit on one side Topic started 31 Mar 2022 15:58, by FrankyBoy Last Post 01 Apr 2022 01:20 by FrankyBoy 1 2	Replies:10 Views:2301	FrankyBoy Last Post by FrankyBoy 01 Apr 2022 01:20
Ethernet Topic started 29 Mar 2022 17:44, by SCLCR-2 Last Post 31 Mar 2022 07:31 by rodw 1 2	Replies:11 Views:2792	Last Post by rodw 31 Mar 2022 07:31
1 axle receives a signal, both axles move Topic started 28 Mar 2022 15:20, by Roger S Last Post 31 Mar 2022 05:50 by Roger S	Replies:5 Views:954	Roger S Last Post by Roger S 31 Mar 2022 05:50
How to parallel port stepper motor driver board Topic started 30 Mar 2022 02:25, by wang Last Post 30 Mar 2022 10:03 by tommylight	Replies:1 Views:1844	Last Post by tommylight 30 Mar 2022 10:03
LinuxCnC 2.9 vs 2.8 Advantages ? Topic started 29 Mar 2022 10:07, by my1987toyota Last Post 29 Mar 2022 22:20 by my1987toyota	Replies:9 Views:4675	Last Post by my1987toyota 29 Mar 2022 22:20
xhc-whb04b-6 not showing up as usb Topic started 29 Mar 2022 20:41, by einarak Last Post 29 Mar 2022 21:51 by einarak	Replies:1 Views:1204	einarak Last Post by einarak 29 Mar 2022 21:51
previous program is loaded Topic started 28 Mar 2022 22:32, by halhsasimon Last Post 29 Mar 2022 11:43 by tommylight	Replies:3 Views:801	Last Post by tommylight 29 Mar 2022 11:43
Does Linuxcnc have the capability for 2D edge digitising. Topic started 26 Apr 2020 22:22, by beefy Last Post 28 Mar 2022 13:31 by pkali 1 2	Replies:10 Views:4466	pkali Last Post by pkali 28 Mar 2022 13:31
Mesa 7i76e stopped working without a known reason Topic started 25 Mar 2022 21:43, by dru Last Post 27 Mar 2022 01:42 by PCW	Replies:5 Views:1137	Last Post by PCW 27 Mar 2022 01:42
Two signals connected to one Output Pin Topic started 10 Jan 2019 00:37, by GradeMind Last Post 25 Mar 2022 19:56 by PCW	Replies:9 Views:4122	Last Post by PCW 25 Mar 2022 19:56
Repair 7i76e card Topic started 06 Dec 2021 19:48, by chris@cnc Last Post 25 Mar 2022 12:04 by chris@cnc	Replies:2 Views:1073	chris@cnc Last Post by chris@cnc 25 Mar 2022 12:04
Changing default of G64 to add parameters or set to G61 Topic started 12 Jan 2021 18:12, by jpvonoy Last Post 25 Mar 2022 07:33 by elf 1 2	Replies:12 Views:4229	elf Last Post by elf 25 Mar 2022 07:33
Commands in LinuxCNC to control specific pins of the DB25 connector..... Topic started 23 Mar 2022 19:02, by sd3534 Last Post 24 Mar 2022 22:15 by andypugh	Replies:5 Views:1477	Last Post by andypugh 24 Mar 2022 22:15
Axis off position Topic started 23 Mar 2022 13:07, by cndewitt Last Post 24 Mar 2022 21:17 by andypugh	Replies:4 Views:845	Last Post by andypugh 24 Mar 2022 21:17

Time to create page: 0.812 seconds