General LinuxCNC Questions 6196 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
MESA 7i97 - connection of DC TachMotor amplifiers - power supplies Topic started 15 Aug 2025 12:13, by Hartwig Last Post 15 Aug 2025 17:30 by Hartwig	Replies:2 Views:670	Hartwig Last Post by Hartwig 15 Aug 2025 17:30
Search for Google document from rodw Topic started 14 Aug 2025 08:15, by Marc_P Last Post 15 Aug 2025 08:43 by rodw	Replies:7 Views:839	Last Post by rodw 15 Aug 2025 08:43
multiple estops on separate pins Topic started 14 Aug 2025 09:59, by LeonDolnicar Last Post 14 Aug 2025 13:11 by tommylight	Replies:6 Views:825	Last Post by tommylight 14 Aug 2025 13:11
Raspbery pi5 pcie adapter to parport card Topic started 12 Aug 2025 23:00, by KaveMan Last Post 14 Aug 2025 04:50 by unknown 1 2	Replies:13 Views:2161	unknown Last Post by unknown 14 Aug 2025 04:50
Tool table crash after reboot or power off Topic started 12 Aug 2025 17:56, by Piton4ik Last Post 13 Aug 2025 16:10 by Piton4ik	Replies:4 Views:665	Piton4ik Last Post by Piton4ik 13 Aug 2025 16:10
Mesa 7i76eu gpio pins not working Topic started 12 Aug 2025 07:41, by LeonDolnicar Last Post 13 Aug 2025 11:08 by LeonDolnicar	Replies:4 Views:845	LeonDolnicar Last Post by LeonDolnicar 13 Aug 2025 11:08
view > mm vs inches, and tool size display, in AXIS Topic started 11 Aug 2025 03:36, by johnbump Last Post 12 Aug 2025 00:32 by johnbump	Replies:2 Views:572	johnbump Last Post by johnbump 12 Aug 2025 00:32
Hardware requirement if a MESA 7i97T card is used Topic started 11 Aug 2025 15:29, by Hartwig Last Post 11 Aug 2025 15:38 by tommylight	Replies:1 Views:669	Last Post by tommylight 11 Aug 2025 15:38
Diving deeper into linuxcnc Topic started 11 Aug 2025 02:43, by arijitdutta Last Post 11 Aug 2025 12:07 by rodw	Replies:1 Views:609	Last Post by rodw 11 Aug 2025 12:07
LinuxCNC vs Commercial Topic started 18 Mar 2015 05:42, by DuNuNuBatman Last Post 10 Aug 2025 20:18 by tommylight 1 2	Replies:15 Views:11.2k	Last Post by tommylight 10 Aug 2025 20:18
GOG53Z0 Topic started 09 Aug 2025 16:09, by bridges67 Last Post 09 Aug 2025 16:33 by MaHa	Replies:1 Views:488	MaHa Last Post by MaHa 09 Aug 2025 16:33
injection mold machine custom gui Topic started 08 Aug 2025 11:08, by Philip Lydin Last Post 08 Aug 2025 22:58 by andypugh	Replies:4 Views:709	Last Post by andypugh 08 Aug 2025 22:58
Bit length checking on top datum Topic started 04 Aug 2025 14:29, by dannym Last Post 08 Aug 2025 19:56 by andypugh	Replies:4 Views:852	Last Post by andypugh 08 Aug 2025 19:56
6i25 encoder not working right. Topic started 07 Aug 2025 07:03, by Kieran Last Post 07 Aug 2025 08:07 by Kieran	Replies:1 Views:627	Kieran Last Post by Kieran 07 Aug 2025 08:07
Calibration issue Topic started 05 Aug 2025 15:04, by RLA Last Post 06 Aug 2025 20:48 by RLA	Replies:6 Views:738	RLA Last Post by RLA 06 Aug 2025 20:48
prevent jog limit error Topic started 04 Aug 2025 13:50, by konrad Last Post 06 Aug 2025 14:53 by konrad	Replies:7 Views:854	konrad Last Post by konrad 06 Aug 2025 14:53
Is my wire diagram correct? Topic started 28 Mar 2021 18:07, by Haugud Last Post 04 Aug 2025 20:44 by PCW 1 2	Replies:14 Views:7262	Last Post by PCW 04 Aug 2025 20:44
Motion Jitter with LinuxCNC + EtherCAT Topic started 31 Jul 2025 12:14, by Abdulkareem Last Post 04 Aug 2025 09:17 by Abdulkareem	Replies:7 Views:1528	Abdulkareem Last Post by Abdulkareem 04 Aug 2025 09:17
Auto mode, reaching first point of coord then "reading" state, no movement Topic started 26 Jul 2025 06:54, by _skinner Last Post 03 Aug 2025 19:54 by andypugh	Replies:4 Views:875	Last Post by andypugh 03 Aug 2025 19:54
Axis and tool length sensor troubles Topic started 14 Jul 2025 14:23, by seuchato Last Post 02 Aug 2025 13:01 by seuchato	Replies:4 Views:848	seuchato Last Post by seuchato 02 Aug 2025 13:01

Time to create page: 0.526 seconds