Advanced Search

Thank you so much PCW and tommy
PCW would that mean I don't connect 22 - SPINDLE- to COM, instead connect OUT4B --> COM and OUT5B --> COM?

Could you share your 3D CAD model? If not, it's not a problem.

Cheers Hakan. I'll have a read through and see what I can come up with.

Edit:
Looks like I need to convert to a U32 unit (for the duty cycle). Hopefully I can get something working within the next few days. 

As far as I'm aware, motion.probe-input only causes the "probe tripped during non probe move" message if the pin goes high during a non-probe move, not if it's already high.
(I know you figured that out, just wanted to state directly that in theory there's no issue with a non-probe move which starts with the probe triggered)
The real issue is, as Andy says, is that the raw probe input is going to bounce and cause the "probe tripped during non probe move" message, and halt the subsequent move/jog.

But, actually, most of the time this behaviour occurs during probing, it's during the deceleration phase of the probe move itself (as you mentioned). This was opened as an issue last year:
github.com/LinuxCNC/linuxcnc/issues/2926
While you can work round this in hal in various ways (many already discussed), ideally I think this should be patched.
When I had this issue I also thought the same as the title of this post, that the probe must be triggering during the pulloff move (on account of the message wording) when actually it was occuring during the probe move itself. This is confusing and the "probe tripped during non probe move" message is somewhere between misleading and incorrect in this context.
The way I see it is that the deceleration phase is definitely part of the probe move, since you can't have a probe move without deceleration. Therefore, it doesn't make sense to claim that a trigger during a probe move deceleration phase should be treated the same way as a trigger during a jog or commanded non-probe move. The fact that this behaviour only seems to be worked around definitely supports this view.

But I get how this might be complicated to patch if it is the case that the motion type can't stay as "probing" and so is set a different motion type, which causes this issue.
I'm assuming that the fix isn't as simple as keeping the motion type as "probing" after the first trigger, because then subsequent bounces would also be registered as triggers to update the probed position variable? And that definitely isn't ideal, if you commanded one probe move, you shouldn't get several updates to the probe result when only the first one is the canonical result.
So ideally you'd just want to set a flag in the motion type used during deceleration to ignore further probe inputs until the end of that move? Or create a new motion type for "probe decelerating" which has this applied by default?

Either way, this doesn't solve the issue of bouncing during the subsequent pulloff moves. But since the pulloff move is typically at a much higher feed, it's far less likely to be affected by this issue.

And yeah, debounce does work for this, and the increased latency isn't actually a huge issue (as long as it is repeatable) if you calibrate the probe on a known artefact at the probing speed(s) you're planning to use. Probe Basic has this built into the probing routines.

But re. your flipflop logic, you're essentially using the same logic I'm using, which is the "dsmono" component from this comment here, which also makes the the probe "sticky":
forum.linuxcnc.org/24-hal-components/423...rrors?start=0#269004 
(In fact I'd recommend reading that thread from the top, lots of good info)
I think the advantages of dsmono (or implementing the same thing using EDGE) over your component are that you don't need to add M64/M65 to your probing routines, and the pulloff move is protected once the "sticky" period expires.

Ok once again.

For the interfaces you want to configure via Network Manager make sure the interface does not have an entry in the network file.

It is quite simple.

This version built on Flex, where would I find the .ui and .py files?

Thank you for posting about the other possible fixes along with their sources.

For me, just pressing the spacebar to select the locale worked fine.

(And yes i was foolishly stuck with this locale issue too, because i didnt know about the "space-bar" to actually mark the required locale in $ sudo menu-config > locale )

perfect!!! it works ! Thanks!

[ATC_1] is not a recognized section name for the calibration tool.
It only works with '[TUNE]', '[JOINT_n]', '[AXIS_l]' or '[SPINDLE_n]' sections.

 

It should work with any version, I have used from 2021.2 to 2024.something

hi!

i wonder why this not work. is it not possible or is there a workarround? 

i add the ATC (carousel.comp) to the ini


in my hal i link it 
 

but on the calibrationscreen i got no new tab

 


is this not possible?! thanks

Hello PCW,

I hope to get some help from you again.
I tried to make a custom bit file consisting of these two files 7i96s_2pwmd and 7i96sd_mpgp1. 7i96s2pwmd for pwmgen (Stepgen 4-) and 7i96sd_mpgp1 for mpg on P1.
I used the enfinity software, but it doesn't work because of a version conflict.
Do you know which efinty version works with the 7i96s firmware from the homepage ? Thanks a lot

hi andy!
i think the right way is to use your carousel.comp.

but i have no idea how to link this up... its complete new to me and i need help to do this.

i try a little bit.. but if i want to go from pocket 1 to pocket 2 i must count a hole 2 times in a spinning gear disc.

i dont know if INDEX is the correct mode.. i dont want that ou think i am stupid... but.. can we do this together? or is there someone who can help me?

thanks

The spindle mount is just something I came up with and made.  Right now it fits a cheap air cooled 80mm 2.2kw spindle, but I can fit a 100mm diameter spindle if I need to.  I machined a hole in the side of the spindle to feed the wiring out of and through the center of the side bearing.  I hope that will save me from tangling up the wiring.   

forum.linuxcnc.org/39-pncconf/50843-loca...ng-on-raspberry-pi-4

ahh.. as explained in this thread, you have to press spacebar to actually select the locale in the sudo menu-config (ha ha)

by typing locale in the terminale, the newly set locale can be confirmed. I have fixed the locale issue now.

so back to the interface settings and network manager.. i still need help there. Thanks again to all!