PnCConf Wizard 734 topics

Point n Click Configuration tool for Mesa Cards

Subject	Replies / Views	Last Post
Error unable to launch after pncconf. Topic started 30 Aug 2022 00:18, by RobKin Last Post 06 Sep 2022 15:36 by tommylight 1 2	Replies:13 Views:778	Last Post by tommylight 06 Sep 2022 15:36
How do PnCConf's Mesa Card 0 I/O tabs' pin numbers correspond to stepconf's? Topic started 28 Jul 2022 14:09, by clunc Last Post 06 Sep 2022 10:14 by clunc 1 2	Replies:15 Views:1210	Last Post by clunc 06 Sep 2022 10:14
7i96s: can't seem to get a stepper enable signal Topic started 03 Sep 2022 17:21, by Dr. John Last Post 04 Sep 2022 01:51 by PCW 1 2	Replies:14 Views:508	Last Post by PCW 04 Sep 2022 01:51
[YES]Is there a way to create/generate firmware .xml from an existing .pin file? Topic started 22 Jul 2022 08:10, by clunc Last Post 30 Aug 2022 18:17 by Andreas_Rackow	Replies:8 Views:535	Andreas_Rackow Last Post by Andreas_Rackow 30 Aug 2022 18:17
Ini file is overwritten Topic started 22 Aug 2022 16:45, by vkhargwanshi Last Post 23 Aug 2022 11:22 by JT	Replies:3 Views:311	Last Post by JT 23 Aug 2022 11:22
Stepgen spindle Topic started 13 Aug 2022 12:21, by gilesclement Last Post 18 Aug 2022 13:52 by PCW	Replies:8 Views:472	Last Post by PCW 18 Aug 2022 13:52
MPG working with joint but not with axis ??? [solved] Topic started 15 Aug 2022 07:39, by JPL Last Post 18 Aug 2022 06:23 by sprintertrd 1 2	Replies:14 Views:883	sprintertrd Last Post by sprintertrd 18 Aug 2022 06:23
PNC config error Topic started 14 Aug 2022 13:09, by rajsekhar Last Post 15 Aug 2022 16:16 by rajsekhar	Replies:8 Views:350	rajsekhar Last Post by rajsekhar 15 Aug 2022 16:16
Parport to 7i92 Topic started 13 Aug 2021 16:13, by looping Last Post 07 Aug 2022 09:27 by looping 1 2 3 ... 7	Replies:60 Views:4981	looping Last Post by looping 07 Aug 2022 09:27
Cycle start/resume pause and external buttons problem (Mesa 7i76e card) Topic started 01 Aug 2022 08:06, by raychar Last Post 04 Aug 2022 15:03 by raychar 1 2	Replies:13 Views:823	raychar Last Post by raychar 04 Aug 2022 15:03
All GPIO pins not shown by PnCConf for 7i96s Topic started 26 Jul 2022 09:08, by vkhargwanshi Last Post 03 Aug 2022 02:04 by vkhargwanshi 1 2	Replies:17 Views:1043	vkhargwanshi Last Post by vkhargwanshi 03 Aug 2022 02:04
Lichaun LCDA357H setup Topic started 19 Oct 2020 18:35, by CaspianCmonster Last Post 28 Jul 2022 15:12 by Todd Zuercher 1 2	Replies:18 Views:2380	Last Post by Todd Zuercher 28 Jul 2022 15:12
Re: the sticky: "5i25 firmware XML files for pncconf" (missing newer files) Topic started 22 Jul 2022 08:02, by clunc Last Post 23 Jul 2022 01:29 by cmorley	Replies:1 Views:211	cmorley Last Post by cmorley 23 Jul 2022 01:29
ISE Project Navigator 14.7 Topic started 21 Jul 2022 08:34, by Manja Last Post 21 Jul 2022 14:12 by PCW	Replies:1 Views:280	Last Post by PCW 21 Jul 2022 14:12
My first steps with LinuxCNC - comments appreciated :) Using Mesa 7i80 and 7i78 Topic started 13 Jul 2022 22:27, by sukandar Last Post 21 Jul 2022 03:49 by PCW 1 2	Replies:13 Views:699	Last Post by PCW 21 Jul 2022 03:49
LinuxCNC 2.9 RPi - PNCconf error Topic started 12 Jul 2022 21:44, by Gifix Last Post 15 Jul 2022 09:50 by Gifix	Replies:5 Views:487	Gifix Last Post by Gifix 15 Jul 2022 09:50
PncConfig Errno 13 during setup Topic started 11 Jul 2022 14:21, by gilesclement Last Post 11 Jul 2022 17:19 by tommylight	Replies:2 Views:244	Last Post by tommylight 11 Jul 2022 17:19
Error running LinuxCNC after setting up with Pncconf Topic started 09 Jul 2022 16:19, by mloser Last Post 09 Jul 2022 16:25 by tommylight	Replies:1 Views:212	Last Post by tommylight 09 Jul 2022 16:25
LinuxCNC 2.8 - PNCconf bug - bad arrow Topic started 06 Jul 2022 14:52, by zz912 Last Post 07 Jul 2022 15:35 by zz912	Replies:3 Views:281	Last Post by zz912 07 Jul 2022 15:35
Cant get servo motors to move during configuration Topic started 03 Jul 2022 21:19, by 42walrustitan Last Post 07 Jul 2022 00:48 by 42walrustitan 1 2	Replies:13 Views:805	42walrustitan Last Post by 42walrustitan 07 Jul 2022 00:48

Time to create page: 0.272 seconds