PnCConf Wizard 875 topics

Point n Click Configuration tool for Mesa Cards

Subject	Replies / Views	Last Post
MESA PWM Topic started 25 Jun 2013 00:48, by eslavko Last Post 20 Jul 2014 11:32 by vre 1 2 3 ... 5	Replies:47 Views:17.2k	vre Last Post by vre 20 Jul 2014 11:32
Problem with endstops and homing with Mesa 5i25 Topic started 08 Jul 2014 03:32, by t1m0n Last Post 08 Jul 2014 20:40 by PCW	Replies:6 Views:2376	Last Post by PCW 08 Jul 2014 20:40
Brother tc-211 in pncConfig Topic started 07 Jul 2014 01:17, by mblaszkiewicz Last Post 08 Jul 2014 03:00 by cmorley	Replies:3 Views:1980	cmorley Last Post by cmorley 08 Jul 2014 03:00
Spindle control with 5i25+7177 Topic started 14 May 2014 00:04, by treichler Last Post 14 May 2014 20:20 by treichler	Replies:2 Views:1784	treichler Last Post by treichler 14 May 2014 20:20
Phase-A pin on the hm2 encoder module? Topic started 13 May 2014 03:47, by tnl.lambert Last Post 13 May 2014 20:22 by PCW	Replies:1 Views:1813	Last Post by PCW 13 May 2014 20:22
Odd 7i76 error Topic started 15 Apr 2014 01:22, by bottleworks Last Post 09 May 2014 14:53 by bottleworks	Replies:5 Views:2323	bottleworks Last Post by bottleworks 09 May 2014 14:53
possible permissions problem Topic started 03 May 2014 03:13, by acecore Last Post 08 May 2014 18:16 by acecore	Replies:5 Views:2046	acecore Last Post by acecore 08 May 2014 18:16
PC won't boot with 5i25 in 1 of 2 avail. PCI slots Topic started 10 Apr 2014 16:03, by akb1212 Last Post 01 May 2014 07:36 by PCW 1 2	Replies:15 Views:6360	Last Post by PCW 01 May 2014 07:36
mesa 5i25 and 7i76 stepgen and pwm Topic started 23 Apr 2014 00:59, by absolut15 Last Post 24 Apr 2014 04:40 by andypugh	Replies:6 Views:2674	Last Post by andypugh 24 Apr 2014 04:40
5i25 - Hardware Step Gen & Par.Port for Spindel. Topic started 25 Mar 2014 17:22, by Ozcnc Last Post 09 Apr 2014 18:15 by Ozcnc	Replies:9 Views:2930	Ozcnc Last Post by Ozcnc 09 Apr 2014 18:15
No Luck with 5i25 & 7i76 Topic started 19 Mar 2014 15:06, by bottleworks Last Post 08 Apr 2014 15:29 by cncbasher 1 2 3	Replies:28 Views:8347	cncbasher Last Post by cncbasher 08 Apr 2014 15:29
5I25 7I77 PNC Config Problems Topic started 05 Apr 2014 07:05, by zajones08 Last Post 06 Apr 2014 03:34 by zajones08	Replies:4 Views:2501	zajones08 Last Post by zajones08 06 Apr 2014 03:34
LinuxCNC not starting Topic started 22 Mar 2014 02:16, by Jerre122 Last Post 04 Apr 2014 01:24 by emcPT 1 2	Replies:12 Views:4708	Last Post by emcPT 04 Apr 2014 01:24
First time setup - 5i25/7i76 Topic started 30 Mar 2014 04:09, by jonesturf Last Post 31 Mar 2014 22:52 by jonesturf 1 2	Replies:13 Views:7539	jonesturf Last Post by jonesturf 31 Mar 2014 22:52
PnC Config error with 5i25 an 7i77 Topic started 05 Feb 2014 14:16, by svsalt Last Post 14 Mar 2014 07:18 by cmorley	Replies:3 Views:2642	cmorley Last Post by cmorley 14 Mar 2014 07:18
Closed loop spindle control Topic started 01 Feb 2014 20:53, by DavidNicholls Last Post 11 Mar 2014 12:59 by cmorley	Replies:6 Views:2984	cmorley Last Post by cmorley 11 Mar 2014 12:59
firmware 5i25,7i85,8i20 brushless servo drive Topic started 05 Mar 2014 04:10, by johns00056 Last Post 09 Mar 2014 02:58 by PCW 1 2 3 4	Replies:30 Views:10.6k	Last Post by PCW 09 Mar 2014 02:58
5i25 w/7i76 external estop setup question Topic started 05 Mar 2014 15:53, by b2unit Last Post 06 Mar 2014 00:32 by PCW	Replies:6 Views:3345	Last Post by PCW 06 Mar 2014 00:32
Cannot select Mesa card in PnCConf? Topic started 25 Feb 2014 06:23, by DaBit Last Post 25 Feb 2014 16:56 by DaBit	Replies:3 Views:2800	DaBit Last Post by DaBit 25 Feb 2014 16:56
MESA 5i25 P2 connector pinout Topic started 23 Feb 2014 21:59, by hreimer Last Post 23 Feb 2014 23:36 by PCW	Replies:1 Views:2467	Last Post by PCW 23 Feb 2014 23:36

Time to create page: 0.164 seconds