Recent Topics (213 topics)

	Subject	Replies / Views	Last Post

	Locations of LinuxCNC Category: Installing LinuxCNC Topic started 06 Jan 2023 13:08, by JT Last Post 30 Nov 2025 19:33 by rodw 1 2 3	Replies:23 Views:19.3k	Last Post by rodw 30 Nov 2025 19:33
	7C80 on RPI5 Category: Driver Boards Topic started 27 Mar 2025 18:39, by torulf Last Post 30 Nov 2025 18:12 by andypugh 1 2	Replies:12 Views:1143	Last Post by andypugh 30 Nov 2025 18:12
	Low voltage limit/home switch configuration Category: Basic Configuration Topic started 29 Nov 2025 19:18, by Autumn Reign Last Post 30 Nov 2025 18:09 by andypugh	Replies:5 Views:266	Last Post by andypugh 30 Nov 2025 18:09
	Machine fails to get past G1 "spindle-at-speed" issue EtherCAT spindle Category: EtherCAT Topic started 29 Nov 2025 22:10, by Will_cnc Last Post 30 Nov 2025 17:10 by Hakan	Replies:7 Views:338	Hakan Last Post by Hakan 30 Nov 2025 17:10
	3D printed stuff, showcase it here Category: Additive Manufacturing Topic started 04 Sep 2021 23:22, by tommylight Last Post 30 Nov 2025 15:44 by my1987toyota 1 2 3 ... 6	Replies:51 Views:24.4k	Last Post by my1987toyota 30 Nov 2025 15:44
	Mesa 7I96s - 5 AXIS Category: Installing LinuxCNC Topic started 26 Nov 2025 18:56, by jmp97 Last Post 30 Nov 2025 10:20 by jmp97 1 2	Replies:11 Views:779	jmp97 Last Post by jmp97 30 Nov 2025 10:20
	Upgrading Linuxcnc on Trixie to 2.97 and later forever Category: Installing LinuxCNC Topic started 30 Nov 2025 07:44, by rodw Last Post 30 Nov 2025 07:44 by rodw	Replies:0 Views:282	Last Post by rodw 30 Nov 2025 07:44
	QCombobox Category: Flex GUI Topic started 14 Nov 2025 00:40, by MaHa Last Post 30 Nov 2025 02:32 by MaHa	Replies:2 Views:396	MaHa Last Post by MaHa 30 Nov 2025 02:32
	Is there any way to use Pncconf Wizard to set up 7i97T with 7i73 pendant board? Category: General LinuxCNC Questions Topic started 29 Nov 2025 14:11, by Tinker Last Post 29 Nov 2025 21:12 by rodw	Replies:4 Views:252	Last Post by rodw 29 Nov 2025 21:12
	carousel.comp scale questions. Category: General LinuxCNC Questions Topic started 23 Nov 2025 08:18, by rasmus Last Post 29 Nov 2025 20:27 by rasmus	Replies:4 Views:340	rasmus Last Post by rasmus 29 Nov 2025 20:27
	Remora SPI: Bad SPI payload, estop won’t reset, SKR 1.4 + RPi4 – config below Category: Computers and Hardware Topic started 26 Oct 2025 10:12, by Chad Last Post 29 Nov 2025 10:49 by Chad	Replies:2 Views:685	Chad Last Post by Chad 29 Nov 2025 10:49
	A flowchart paranoid (a story about source code documentation) Category: LinuxCNC Documents Topic started 22 Nov 2025 05:03, by abu Last Post 29 Nov 2025 07:42 by Aciera	Replies:4 Views:775	Last Post by Aciera 29 Nov 2025 07:42
	QtPlasmaC – Magic Comments not creating materials from G-code Category: Plasmac Topic started 27 Nov 2025 11:34, by MTTI Last Post 29 Nov 2025 02:28 by snowgoer540	Replies:6 Views:375	Last Post by snowgoer540 29 Nov 2025 02:28

Statistics

Total Messages: 280238
Total Sections: 7
Today Open: 2
Today Total Answer: 27

Total Subjects: 23384
Total Categories: 54
Yesterday Open: 7
Yesterday Total Answer: 33

Total Users: 10438
Latest Member: 123ERDEM

Time to create page: 0.226 seconds

Powered by Kunena Forum