General LinuxCNC Questions 6772 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
Steps required to actually get table to move? Topic started 22 Jan 2024 00:24, by slowpoke Last Post 26 Jan 2024 22:06 by PCW	Replies:3 Views:547	Last Post by PCW 26 Jan 2024 22:06
Considering building a small hobby CNC Plasma Topic started 19 May 2019 21:22, by Clive S Last Post 26 Jan 2024 13:05 by RaSu 1 2 3	Replies:22 Views:3721	RaSu Last Post by RaSu 26 Jan 2024 13:05
Controller for old Shopbot Topic started 24 Jan 2024 21:10, by poopsmith76 Last Post 25 Jan 2024 23:18 by poopsmith76	Replies:4 Views:557	Last Post by poopsmith76 25 Jan 2024 23:18
Kernel Topic started 24 Jan 2024 23:20, by garja Last Post 25 Jan 2024 20:19 by garja	Replies:5 Views:700	garja Last Post by garja 25 Jan 2024 20:19
Help with sources.list Topic started 23 Jan 2024 16:35, by wisao Last Post 25 Jan 2024 10:10 by rodw	Replies:1 Views:780	Last Post by rodw 25 Jan 2024 10:10
5 axis motor parameters Topic started 23 Jan 2024 06:44, by Duatepe Last Post 24 Jan 2024 10:14 by Duatepe 1 2	Replies:18 Views:1514	Duatepe Last Post by Duatepe 24 Jan 2024 10:14
Having problems with stepper enable driven relay enabled on linux boot Topic started 22 Jan 2024 19:52, by reBrick Last Post 24 Jan 2024 07:42 by reBrick	Replies:2 Views:495	reBrick Last Post by reBrick 24 Jan 2024 07:42
Raspberry pi 5 Topic started 18 Jan 2024 07:17, by rohit269 Last Post 24 Jan 2024 06:06 by rohit269 1 2	Replies:12 Views:3459	rohit269 Last Post by rohit269 24 Jan 2024 06:06
Python Interface makes race conditions - mayby Topic started 01 Jan 2024 12:53, by zz912 Last Post 23 Jan 2024 19:53 by zz912 1 2 3	Replies:23 Views:2777	Last Post by zz912 23 Jan 2024 19:53
CNC Sewing machine question Topic started 03 Aug 2019 23:02, by rjd1234 Last Post 23 Jan 2024 18:27 by tommylight 1 2 3 ... 8	Replies:76 Views:13.9k	Last Post by tommylight 23 Jan 2024 18:27
Velocity controlled servo ? Topic started 22 Jan 2024 09:37, by qwertyqwq Last Post 23 Jan 2024 16:05 by juliankoenig87	Replies:6 Views:578	juliankoenig87 Last Post by juliankoenig87 23 Jan 2024 16:05
Ayuda para un principiante Topic started 21 Jan 2024 02:52, by Ray_TL00 Last Post 22 Jan 2024 19:29 by chris@cnc	Replies:1 Views:517	chris@cnc Last Post by chris@cnc 22 Jan 2024 19:29
Automatic change of lathe tools. Topic started 21 Jan 2024 18:52, by jarcysgru Last Post 22 Jan 2024 08:41 by jarcysgru	Replies:4 Views:554	jarcysgru Last Post by jarcysgru 22 Jan 2024 08:41
XHC-HB04B pendant with a new/different USB device ID Topic started 22 Jan 2024 00:30, by bcunningham Last Post 22 Jan 2024 01:15 by bcunningham	Replies:1 Views:348	bcunningham Last Post by bcunningham 22 Jan 2024 01:15
Is there a sim config example that's using LIMIT_AXIS component? Topic started 21 Jan 2024 18:56, by vmihalca Last Post 21 Jan 2024 19:22 by tommylight	Replies:1 Views:482	Last Post by tommylight 21 Jan 2024 19:22
Using G95 on a simulator Topic started 10 Jan 2024 16:36, by n_spect_r Last Post 21 Jan 2024 10:43 by n_spect_r	Replies:2 Views:483	n_spect_r Last Post by n_spect_r 21 Jan 2024 10:43
Introduction along with some questions regarding LinuxCNC Topic started 20 Jan 2024 07:57, by arijitdutta Last Post 21 Jan 2024 06:29 by tommylight 1 2	Replies:16 Views:1474	Last Post by tommylight 21 Jan 2024 06:29
Does Linux CNC support Closed loop with Steppers? Topic started 02 Feb 2021 14:49, by Craig E Last Post 21 Jan 2024 03:03 by Ray_TL00 1 2	Replies:16 Views:5227	Ray_TL00 Last Post by Ray_TL00 21 Jan 2024 03:03
RPI4 + 7c81+g540 hal/ini Topic started 19 Jan 2024 14:44, by jaketoolco Last Post 20 Jan 2024 15:46 by PCW	Replies:3 Views:424	Last Post by PCW 20 Jan 2024 15:46
2.9.2 issue: The initial stat.5x_offset is 0 instead of 1 Topic started 19 Jan 2024 20:47, by vmihalca Last Post 20 Jan 2024 13:29 by vmihalca	Replies:2 Views:429	vmihalca Last Post by vmihalca 20 Jan 2024 13:29

Time to create page: 0.432 seconds