Basic Configuration 1322 topics

A place to discuss basic configurations like probe input, homing etc.

Subject	Replies / Views	Last Post
Rotary table configuration Topic started 08 Mar 2016 01:18, by Sparky961 Last Post 31 Mar 2016 08:52 by andypugh 1 2 3 ... 5	Replies:43 Views:10.6k	Last Post by andypugh 31 Mar 2016 08:52
Recording min/max values from HAL Topic started 30 Mar 2016 21:05, by Sparky961 Last Post 30 Mar 2016 22:19 by Sparky961	Replies:1 Views:1286	Last Post by Sparky961 30 Mar 2016 22:19
Basic help on configuring stepconf Topic started 20 Mar 2016 21:48, by kt600v Last Post 29 Mar 2016 14:34 by andypugh	Replies:1 Views:1439	Last Post by andypugh 29 Mar 2016 14:34
Problem after homing Topic started 22 Mar 2016 10:28, by Urri Last Post 22 Mar 2016 19:14 by Todd Zuercher	Replies:7 Views:1554	Last Post by Todd Zuercher 22 Mar 2016 19:14
Help on basic configuration with stepconf Topic started 20 Mar 2016 21:39, by kt600v Last Post 21 Mar 2016 18:56 by cmorley	Replies:2 Views:1617	cmorley Last Post by cmorley 21 Mar 2016 18:56
mesa 7i76 configuring a spindle encoder Topic started 15 Mar 2016 13:09, by Clive S Last Post 21 Mar 2016 10:01 by Clive S 1 2 3 ... 5	Replies:46 Views:11.4k	Clive S Last Post by Clive S 21 Mar 2016 10:01
Tool length offset and Part Zero Topic started 17 Mar 2016 09:11, by nicokid Last Post 20 Mar 2016 22:11 by eFalegname	Replies:3 Views:3023	Last Post by eFalegname 20 Mar 2016 22:11
Configuration with Timing Belt Topic started 19 Mar 2016 15:51, by spaceghost Last Post 20 Mar 2016 05:27 by Rick G	Replies:6 Views:3886	Last Post by Rick G 20 Mar 2016 05:27
Help with homing mesa 7i76 Topic started 13 Mar 2016 09:08, by Clive S Last Post 15 Mar 2016 23:38 by BigJohnT	Replies:5 Views:1921	Last Post by BigJohnT 15 Mar 2016 23:38
Servo Rotation. Topic started 11 Mar 2016 19:45, by marsheng Last Post 13 Mar 2016 22:44 by andypugh	Replies:1 Views:1247	Last Post by andypugh 13 Mar 2016 22:44
No Jog without homing Topic started 11 Mar 2016 22:06, by verdi Last Post 12 Mar 2016 23:36 by cmorley	Replies:6 Views:3327	cmorley Last Post by cmorley 12 Mar 2016 23:36
What type of wire to connect stepers Topic started 07 Mar 2016 19:26, by gizmo6023 Last Post 12 Mar 2016 01:37 by gizmo6023 1 2	Replies:12 Views:3833	gizmo6023 Last Post by gizmo6023 12 Mar 2016 01:37
Sain Smart 5 axis (Blue) break out board input ? Topic started 28 Feb 2016 01:44, by gizmo6023 Last Post 11 Mar 2016 21:04 by gizmo6023	Replies:8 Views:3993	gizmo6023 Last Post by gizmo6023 11 Mar 2016 21:04
Servo setup with integrated PID Topic started 08 Mar 2016 01:20, by buckym1a Last Post 10 Mar 2016 22:29 by buckym1a	Replies:4 Views:2275	buckym1a Last Post by buckym1a 10 Mar 2016 22:29
using a hand wheel encoder Topic started 29 Aug 2015 23:36, by Clive S Last Post 10 Mar 2016 17:38 by PCW 1 2 3	Replies:25 Views:11.8k	Last Post by PCW 10 Mar 2016 17:38
Need Help with Mesa 5i20 Stepgen Config Topic started 06 Mar 2016 23:20, by BartyBorris Last Post 07 Mar 2016 02:34 by PCW	Replies:9 Views:1758	Last Post by PCW 07 Mar 2016 02:34
MPG: axis.N.jog-vel-mode doesn't work as expected? Topic started 02 Mar 2016 00:58, by Sparky961 Last Post 02 Mar 2016 13:21 by andypugh	Replies:8 Views:2349	Last Post by andypugh 02 Mar 2016 13:21
Spindle Step/Dir Topic started 15 Jun 2013 20:30, by jbradshaw Last Post 29 Feb 2016 13:48 by jbradshaw	Replies:6 Views:5779	jbradshaw Last Post by jbradshaw 29 Feb 2016 13:48
Difference between USER_M_PATH and nc_files path Topic started 24 Feb 2016 00:15, by nicokid Last Post 29 Feb 2016 00:27 by nicokid 1 2	Replies:10 Views:4822	Last Post by nicokid 29 Feb 2016 00:27
Spindle Control HAL code error Topic started 28 Feb 2016 03:12, by kineng64 Last Post 28 Feb 2016 07:08 by cmorley	Replies:1 Views:1509	cmorley Last Post by cmorley 28 Feb 2016 07:08

Time to create page: 0.161 seconds