StepConf Wizard 574 topics

Stepper Configuration Wizard for Parallel Port

Forum Header

Subject	Replies / Views	Last Post
Without axis limit switches diy lathe Topic started 26 Jul 2019 18:41, by Dinuka_Shehan Last Post 26 Jul 2019 18:48 by tommylight	Replies:1 Views:933	Last Post by tommylight 26 Jul 2019 18:48
Bridgeport R2E Series 1 Mill with Servos Topic started 11 Jul 2019 21:42, by Fredrs Last Post 15 Jul 2019 21:28 by tommylight	Replies:8 Views:1168	Last Post by tommylight 15 Jul 2019 21:28
Can I connect a NPN inductive home switch direct to my BOB or do I need a relay? Topic started 01 Jul 2019 19:23, by tom-rock Last Post 02 Jul 2019 22:43 by andypugh	Replies:2 Views:1650	Last Post by andypugh 02 Jul 2019 22:43
Joints and step time configuration for open loop stepper system Topic started 01 Jul 2019 14:58, by richard123 Last Post 02 Jul 2019 22:34 by andypugh	Replies:3 Views:1035	Last Post by andypugh 02 Jul 2019 22:34
Plasma torch Topic started 31 May 2019 08:01, by getyers Last Post 26 Jun 2019 00:40 by Grotius	Replies:4 Views:1896	Last Post by Grotius 26 Jun 2019 00:40
Io error step conf Topic started 14 May 2019 07:18, by phoenix Last Post 16 May 2019 06:38 by pl7i92	Replies:4 Views:1227	Last Post by pl7i92 16 May 2019 06:38
MESA 7i76 - Generate a given number of pulses. Topic started 14 May 2019 11:02, by HalaszAttila Last Post 14 May 2019 13:23 by PCW	Replies:1 Views:948	Last Post by PCW 14 May 2019 13:23
Homing Z wants to home X first. Topic started 28 Apr 2019 22:09, by allistar Last Post 12 May 2019 16:42 by pl7i92 1 2	Replies:12 Views:2729	Last Post by pl7i92 12 May 2019 16:42
This is an example of what I am trying to accomplish : Topic started 08 Apr 2019 00:27, by Dragonbitscnc Last Post 27 Apr 2019 21:12 by Dragonbitscnc 1 2	Replies:13 Views:3789	Dragonbitscnc Last Post by Dragonbitscnc 27 Apr 2019 21:12
XYZ B config for and XYZ A machine Topic started 02 Apr 2019 09:23, by Szymik Last Post 04 Apr 2019 09:41 by andypugh	Replies:4 Views:1461	Last Post by andypugh 04 Apr 2019 09:41
Spindle operation setting Topic started 02 Apr 2019 12:51, by Doc Last Post 03 Apr 2019 19:26 by Doc	Replies:2 Views:1221	Doc Last Post by Doc 03 Apr 2019 19:26
Parport Base Address and Launch my mill app (using Virtual Box, no mill, etc) Topic started 19 Mar 2019 16:18, by NullStudent Last Post 21 Mar 2019 06:58 by pl7i92 1 2	Replies:11 Views:3633	Last Post by pl7i92 21 Mar 2019 06:58
AXIS CONFIGURATION Question Topic started 12 Mar 2019 23:25, by sandman92k Last Post 18 Mar 2019 07:20 by pl7i92 1 2	Replies:18 Views:3637	Last Post by pl7i92 18 Mar 2019 07:20
Cant pull input pins of parallel port to GND, BB broken? Topic started 09 Mar 2019 20:39, by tom-rock Last Post 12 Mar 2019 15:36 by tom-rock	Replies:2 Views:1100	tom-rock Last Post by tom-rock 12 Mar 2019 15:36
jog speed Topic started 09 Mar 2019 08:36, by deslee848 Last Post 11 Mar 2019 04:43 by deslee848	Replies:7 Views:2886	deslee848 Last Post by deslee848 11 Mar 2019 04:43
how to enter 3 timing pulley? Topic started 07 Mar 2019 07:39, by deslee848 Last Post 07 Mar 2019 16:34 by pl7i92	Replies:3 Views:1141	Last Post by pl7i92 07 Mar 2019 16:34
gmoccappy and stepconf wizard's files Topic started 06 Mar 2019 19:07, by celalcnc Last Post 07 Mar 2019 07:56 by pl7i92	Replies:2 Views:1113	Last Post by pl7i92 07 Mar 2019 07:56
Need help with estop Topic started 03 Mar 2019 02:06, by brettw Last Post 05 Mar 2019 07:48 by pl7i92	Replies:5 Views:1059	Last Post by pl7i92 05 Mar 2019 07:48
parallel port driver issues, I think Topic started 16 Feb 2019 17:52, by LeonF Last Post 01 Mar 2019 12:44 by andypugh	Replies:8 Views:1309	Last Post by andypugh 01 Mar 2019 12:44
Laucher does not run stepper motors_Axis runs fine. Topic started 15 Feb 2019 18:01, by JackB1 Last Post 16 Feb 2019 18:19 by JackB1	Replies:3 Views:984	Last Post by JackB1 16 Feb 2019 18:19

Time to create page: 0.408 seconds