StepConf Wizard 595 topics

Stepper Configuration Wizard for Parallel Port

Forum Header

Subject	Replies / Views	Last Post
gmoccappy and stepconf wizard's files Topic started 06 Mar 2019 19:07, by celalcnc Last Post 07 Mar 2019 07:56 by pl7i92	Replies:2 Views:1505	Last Post by pl7i92 07 Mar 2019 07:56
Need help with estop Topic started 03 Mar 2019 02:06, by brettw Last Post 05 Mar 2019 07:48 by pl7i92	Replies:5 Views:1553	Last Post by pl7i92 05 Mar 2019 07:48
parallel port driver issues, I think Topic started 16 Feb 2019 17:52, by LeonF Last Post 01 Mar 2019 12:44 by andypugh	Replies:8 Views:1744	Last Post by andypugh 01 Mar 2019 12:44
Laucher does not run stepper motors_Axis runs fine. Topic started 15 Feb 2019 18:01, by JackB1 Last Post 16 Feb 2019 18:19 by JackB1	Replies:3 Views:1355	Last Post by JackB1 16 Feb 2019 18:19
Newbie in need of help Topic started 15 Feb 2019 18:17, by JackB1 Last Post 16 Feb 2019 16:56 by pl7i92	Replies:1 Views:1806	Last Post by pl7i92 16 Feb 2019 16:56
Setting up step conf when using a gearbox Topic started 14 Feb 2019 17:30, by MONKEY0683 Last Post 15 Feb 2019 13:52 by Todd Zuercher	Replies:5 Views:1562	Last Post by Todd Zuercher 15 Feb 2019 13:52
back down the stepper timing rabbit hole.... Topic started 12 Feb 2019 17:24, by IrishMoss Last Post 13 Feb 2019 01:33 by IrishMoss	Replies:6 Views:1459	IrishMoss Last Post by IrishMoss 13 Feb 2019 01:33
Axis configuration Topic started 12 Feb 2019 02:28, by sandman92k Last Post 12 Feb 2019 03:06 by Leon82	Replies:1 Views:2043	Leon82 Last Post by Leon82 12 Feb 2019 03:06
Driver Timing Settings Topic started 10 Feb 2019 22:24, by sandman92k Last Post 11 Feb 2019 03:17 by sandman92k	Replies:3 Views:3281	sandman92k Last Post by sandman92k 11 Feb 2019 03:17
cnc 5 axis Topic started 09 Feb 2019 03:41, by gois Last Post 10 Feb 2019 20:32 by gois	Replies:2 Views:1525	gois Last Post by gois 10 Feb 2019 20:32
Configuring A rotary axis to substitute for the Y axis Topic started 25 Jan 2019 22:12, by Chris401 Last Post 02 Feb 2019 15:02 by andypugh 1 2	Replies:18 Views:4589	Last Post by andypugh 02 Feb 2019 15:02
Holding a pin on? Topic started 12 Jan 2019 19:35, by Matthew_Jones Last Post 14 Jan 2019 01:19 by cmorley	Replies:8 Views:2132	cmorley Last Post by cmorley 14 Jan 2019 01:19
spindle speed configuration, odd PWM range Topic started 02 Jan 2019 19:20, by tonydiethelm Last Post 06 Jan 2019 20:57 by andypugh	Replies:2 Views:1510	Last Post by andypugh 06 Jan 2019 20:57
Reversing Spindle Direction for Machine Tapping Topic started 01 Jan 2019 22:47, by waynegramlich Last Post 06 Jan 2019 19:55 by waynegramlich	Replies:7 Views:1867	waynegramlich Last Post by waynegramlich 06 Jan 2019 19:55
spindle speed configuration question Topic started 30 Dec 2018 20:56, by tonydiethelm Last Post 06 Jan 2019 13:20 by pl7i92	Replies:4 Views:1584	Last Post by pl7i92 06 Jan 2019 13:20
spindle speed backwards? Topic started 30 Dec 2018 06:45, by tonydiethelm Last Post 02 Jan 2019 03:37 by tonydiethelm	Replies:4 Views:1687	tonydiethelm Last Post by tonydiethelm 02 Jan 2019 03:37
7i76 in spindle velocity mode Topic started 26 Dec 2018 09:18, by Skidloaders1 Last Post 26 Dec 2018 15:27 by PCW	Replies:1 Views:1418	Last Post by PCW 26 Dec 2018 15:27
Charge Pump BASE_PERIOD = 100000 12,5kHz 5khz Topic started 08 Dec 2018 13:41, by Adam Maszynotwór Last Post 13 Dec 2018 18:00 by PCW	Replies:5 Views:2143	Last Post by PCW 13 Dec 2018 18:00
Chinese 6040 CNC Topic started 28 Jun 2018 01:41, by pootaholic Last Post 04 Dec 2018 06:07 by pootaholic	Replies:9 Views:4878	Last Post by pootaholic 04 Dec 2018 06:07
X Axis is drifting and wondered if my settings are to blame? Topic started 03 Dec 2018 09:52, by uptown47 Last Post 03 Dec 2018 18:40 by uptown47	Replies:2 Views:1988	uptown47 Last Post by uptown47 03 Dec 2018 18:40

Time to create page: 0.197 seconds