Driver Boards 2440 topics

Discussion on add on driver boards

Subject	Replies / Views	Last Post
Additional encoder on 7i92-7i77 - Do i need a new bitfile? Topic started 04 May 2020 06:54, by Henk Last Post 04 May 2020 17:14 by tommylight	Replies:7 Views:1420	Last Post by tommylight 04 May 2020 17:14
Strange 7i76e problem when starting linuxcnc Topic started 01 Feb 2020 18:17, by timfaber Last Post 03 May 2020 18:35 by PCW 1 2 3	Replies:25 Views:5843	Last Post by PCW 03 May 2020 18:35
7i96 quit working Topic started 01 May 2020 19:28, by mrmike Last Post 01 May 2020 22:38 by PCW	Replies:7 Views:1214	Last Post by PCW 01 May 2020 22:38
Mesa 7i73 wiring question Topic started 01 May 2020 09:49, by rodw Last Post 01 May 2020 14:01 by Mike_Eitel	Replies:4 Views:1268	Last Post by Mike_Eitel 01 May 2020 14:01
Error finishing read mesa 7i96 Topic started 27 Apr 2020 09:53, by Clive S Last Post 27 Apr 2020 14:36 by PCW	Replies:5 Views:2120	Last Post by PCW 27 Apr 2020 14:36
7I96 vs 7i76e Topic started 11 Jun 2019 19:42, by ihavenofish Last Post 26 Apr 2020 15:00 by PCW	Replies:5 Views:4407	Last Post by PCW 26 Apr 2020 15:00
hm2_pci complaining: inconsistent Module Descriptor for UART Transmit Channel Topic started 24 Apr 2020 00:27, by owhite Last Post 24 Apr 2020 14:17 by PCW	Replies:4 Views:1236	Last Post by PCW 24 Apr 2020 14:17
Mesa 7i85S mounting blocks Topic started 23 Apr 2020 00:10, by helioz2000 Last Post 23 Apr 2020 10:30 by tommylight	Replies:1 Views:1429	Last Post by tommylight 23 Apr 2020 10:30
working on getting stepper signals out of mesa 6i24 board Topic started 22 Apr 2020 01:42, by owhite Last Post 22 Apr 2020 02:32 by owhite	Replies:4 Views:1390	Last Post by owhite 22 Apr 2020 02:32
Mesa card suggestion Topic started 21 Apr 2020 17:43, by nicber Last Post 21 Apr 2020 19:59 by nicber	Replies:5 Views:1310	nicber Last Post by nicber 21 Apr 2020 19:59
can not connect to Mesa 7i76E anymore Topic started 16 Apr 2020 14:11, by Christoph Last Post 21 Apr 2020 15:15 by PCW	Replies:7 Views:1727	Last Post by PCW 21 Apr 2020 15:15
Stepper Drive Enable Circuit Topic started 18 Apr 2020 17:29, by Project_Hopeless Last Post 20 Apr 2020 21:07 by PCW	Replies:5 Views:2220	Last Post by PCW 20 Apr 2020 21:07
computer / linuxcnc unable to detect mesanet 6i24 board Topic started 18 Apr 2020 19:25, by owhite Last Post 18 Apr 2020 22:43 by PCW 1 2 3	Replies:22 Views:5312	Last Post by PCW 18 Apr 2020 22:43
Spindle controler Meccanica Cortini L300 sensing brake Topic started 18 Apr 2020 01:25, by alkabal Last Post 18 Apr 2020 08:35 by bbsr_5a	Replies:1 Views:2391	bbsr_5a Last Post by bbsr_5a 18 Apr 2020 08:35
Power supply selection for stepper based config Topic started 15 Apr 2020 20:38, by alkabal Last Post 18 Apr 2020 00:57 by alkabal 1 2	Replies:18 Views:3135	alkabal Last Post by alkabal 18 Apr 2020 00:57
6i25/7i76 TB3 Encoder Jumper Settings - mixed mode possible? Topic started 17 Apr 2020 22:19, by Joco Last Post 17 Apr 2020 22:24 by PCW	Replies:1 Views:1152	Last Post by PCW 17 Apr 2020 22:24
Can't Ping 7i76 Topic started 15 Apr 2020 19:09, by cncbeagle Last Post 15 Apr 2020 20:23 by PCW	Replies:3 Views:1566	Last Post by PCW 15 Apr 2020 20:23
7i76 repair? Topic started 14 Apr 2020 17:23, by VVO Last Post 15 Apr 2020 01:54 by PCW	Replies:9 Views:1492	Last Post by PCW 15 Apr 2020 01:54
7i76: pwm output stuck high Topic started 11 Apr 2020 09:34, by johnbl Last Post 14 Apr 2020 13:08 by PCW 1 2	Replies:11 Views:2897	Last Post by PCW 14 Apr 2020 13:08
constraints on the pin configuration for 6i24 Topic started 14 Apr 2020 02:53, by owhite Last Post 14 Apr 2020 04:02 by owhite	Replies:2 Views:1141	Last Post by owhite 14 Apr 2020 04:02

Time to create page: 0.277 seconds