General LinuxCNC Questions 6052 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
3d kantentaster und werkzeuglängen Taste Topic started 27 Dec 2025 06:42, by AndyUAZ Last Post 03 Jan 2026 10:24 by AndyUAZ	Replies:3 Views:301	AndyUAZ Last Post by AndyUAZ 03 Jan 2026 10:24
7i97t Mesaflash Problem Topic started 29 Dec 2025 18:46, by Robin123 Last Post 02 Jan 2026 16:43 by PCW 1 2 3	Replies:27 Views:958	Last Post by PCW 02 Jan 2026 16:43
MESA 1I76EU Firmware Topic started 31 Dec 2025 04:32, by Bendandsend Last Post 31 Dec 2025 13:37 by tommylight	Replies:1 Views:222	Last Post by tommylight 31 Dec 2025 13:37
Following errors Topic started 14 Jun 2023 09:11, by ALR85 Last Post 30 Dec 2025 19:44 by tommylight 1 2 3	Replies:21 Views:3248	Last Post by tommylight 30 Dec 2025 19:44
Python LinuxCNC module Topic started 29 Dec 2025 22:19, by hhscott Last Post 30 Dec 2025 05:17 by rodw	Replies:1 Views:269	Last Post by rodw 30 Dec 2025 05:17
7I84U multiplex control panel switches Topic started 30 Dec 2025 01:31, by rmavalente Last Post 30 Dec 2025 03:27 by PCW	Replies:1 Views:183	Last Post by PCW 30 Dec 2025 03:27
Linuxcnc Image for Raspberry Pi 3 Topic started 29 Nov 2021 17:24, by tsewell Last Post 24 Dec 2025 05:57 by NWE 1 2 3	Replies:20 Views:10.4k	Last Post by NWE 24 Dec 2025 05:57
Moderator Notice Regarding Links To Unsanctioned Mirrors - Clarfication. Topic started 16 Dec 2025 01:12, by unknown Last Post 16 Dec 2025 04:11 by unknown	Replies:4 Views:358	unknown Last Post by unknown 16 Dec 2025 04:11
Gerber Sabre 408 - 404 Retrofit Topic started 09 Dec 2025 14:05, by thsobota Last Post 13 Dec 2025 05:51 by NWE	Replies:2 Views:463	Last Post by NWE 13 Dec 2025 05:51
LinuxCNC python Topic started 21 Nov 2025 17:25, by kwanlokto Last Post 09 Dec 2025 12:02 by JT	Replies:2 Views:373	Last Post by JT 09 Dec 2025 12:02
Bimanual Operation (Paused/Resume) in Homing Process Topic started 07 Dec 2025 22:02, by rbobey1989 Last Post 09 Dec 2025 05:12 by rbobey1989	Replies:2 Views:314	Last Post by rbobey1989 09 Dec 2025 05:12
Hybrid Manual/Stepper Control Topic started 04 Dec 2025 10:41, by voltaicsca Last Post 09 Dec 2025 04:55 by timo	Replies:7 Views:462	timo Last Post by timo 09 Dec 2025 04:55
wait_complete() Topic started 30 Aug 2021 12:27, by RKtech Last Post 07 Dec 2025 23:32 by jcdammeyer	Replies:5 Views:1594	Last Post by jcdammeyer 07 Dec 2025 23:32
Remora (SKR 1.4 RPi) – massive SPI noise, “bad payload” communication fails Topic started 01 Dec 2025 19:21, by Chad Last Post 02 Dec 2025 15:34 by Chad	Replies:5 Views:471	Chad Last Post by Chad 02 Dec 2025 15:34
Is the wiki down? Topic started 01 Dec 2025 03:31, by tdonia Last Post 01 Dec 2025 11:21 by unknown	Replies:2 Views:264	unknown Last Post by unknown 01 Dec 2025 11:21
Problem with linear movement Topic started 30 Nov 2025 20:17, by MaHa Last Post 01 Dec 2025 07:28 by MaHa	Replies:2 Views:303	MaHa Last Post by MaHa 01 Dec 2025 07:28
Is there any way to use Pncconf Wizard to set up 7i97T with 7i73 pendant board? Topic started 29 Nov 2025 14:11, by Tinker Last Post 29 Nov 2025 21:12 by rodw	Replies:4 Views:379	Last Post by rodw 29 Nov 2025 21:12
carousel.comp scale questions. Topic started 23 Nov 2025 08:18, by rasmus Last Post 29 Nov 2025 20:27 by rasmus	Replies:4 Views:423	rasmus Last Post by rasmus 29 Nov 2025 20:27
LinuxCNC 2.9.3 .xz image for RPi 5 is not available in the ISO directory Topic started 19 Nov 2025 04:40, by 4ashishkr Last Post 28 Nov 2025 21:41 by andypugh	Replies:4 Views:410	Last Post by andypugh 28 Nov 2025 21:41
EtherCAT + CiA402 Servo: OP state reached, but axis won’t move (only Following E Topic started 15 Nov 2025 22:52, by aDm1N Last Post 28 Nov 2025 21:33 by aDm1N 1 2	Replies:11 Views:2102	Last Post by aDm1N 28 Nov 2025 21:33

Time to create page: 0.422 seconds