Plasmac 667 topics

A place to ask questions about the Plasmac interface

Subject	Replies / Views	Last Post
Variable trigger error Topic started 05 Jul 2022 16:25, by paulsao Last Post 05 Jul 2022 20:05 by snowgoer540	Replies:4 Views:595	Last Post by snowgoer540 05 Jul 2022 20:05
gcode not found Topic started 30 Jun 2022 15:04, by wade956 Last Post 01 Jul 2022 14:14 by wade956	Replies:4 Views:758	Last Post by wade956 01 Jul 2022 14:14
Update qtplasmac to latest with system from buildbot Topic started 13 Jun 2022 15:47, by bevins Last Post 29 Jun 2022 04:13 by CFE 1 2 3	Replies:24 Views:2832	CFE Last Post by CFE 29 Jun 2022 04:13
Homing Issue "home switch inactive before backoff" Topic started 16 Jun 2022 07:08, by little_sparky Last Post 24 Jun 2022 16:24 by PCW	Replies:9 Views:1401	Last Post by PCW 24 Jun 2022 16:24
Is it possible to disable ARC_OK and still have THC UP/DOWN working? Topic started 23 Jun 2022 13:36, by fernandosf Last Post 23 Jun 2022 17:58 by fernandosf	Replies:5 Views:699	Last Post by fernandosf 23 Jun 2022 17:58
QTPlasmac interpreting Sheetcam material selection, M190 Topic started 23 Jun 2022 02:02, by LinfieldGarage Last Post 23 Jun 2022 12:29 by LinfieldGarage	Replies:4 Views:841	LinfieldGarage Last Post by LinfieldGarage 23 Jun 2022 12:29
THCAD-10 Arc voltage not sensoring plate Topic started 31 May 2022 09:24, by aabtech Last Post 19 Jun 2022 13:30 by tommylight	Replies:1 Views:1029	Last Post by tommylight 19 Jun 2022 13:30
Latest post processor Topic started 17 Jun 2022 11:32, by bevins Last Post 18 Jun 2022 23:51 by phillc54	Replies:2 Views:899	Last Post by phillc54 18 Jun 2022 23:51
Non-slip plate cutting Topic started 15 Jun 2022 12:42, by paulsao Last Post 16 Jun 2022 06:13 by Clive S	Replies:4 Views:729	Clive S Last Post by Clive S 16 Jun 2022 06:13
Ohmic probe a inssues water table Topic started 02 Apr 2022 19:15, by paulsao Last Post 14 Jun 2022 00:12 by Tsf62 1 2	Replies:10 Views:2637	Tsf62 Last Post by Tsf62 14 Jun 2022 00:12
WARNING FOR USERS THAT RUN BUSTER Topic started 04 Jun 2022 11:40, by phillc54 Last Post 10 Jun 2022 00:59 by tommylight	Replies:2 Views:886	Last Post by tommylight 10 Jun 2022 00:59
Initial Height Skip (IHS) not functioning properly Topic started 24 May 2022 19:59, by Uthayne Last Post 08 Jun 2022 07:38 by phillc54 1 2	Replies:14 Views:2056	Last Post by phillc54 08 Jun 2022 07:38
How to configure THCAD-10 arc voltage Topic started 02 Jun 2022 06:37, by aabtech Last Post 05 Jun 2022 18:06 by aabtech	Replies:6 Views:1093	Last Post by aabtech 05 Jun 2022 18:06
Thanks for the QTPlasmaC Conversational Development Topic started 01 Jun 2022 19:45, by robertspark Last Post 01 Jun 2022 19:51 by snowgoer540	Replies:2 Views:900	Last Post by snowgoer540 01 Jun 2022 19:51
Using one stepper Driver with two stepper motor Topic started 25 May 2022 09:24, by aabtech Last Post 30 May 2022 00:50 by andypugh	Replies:7 Views:864	Last Post by andypugh 30 May 2022 00:50
Thcad ohmic probe1 Topic started 24 May 2022 10:51, by paulsao Last Post 24 May 2022 11:18 by paulsao	Replies:2 Views:610	Last Post by paulsao 24 May 2022 11:18
Mesa 7i92 board problem Topic started 30 Apr 2022 11:49, by aabtech Last Post 24 May 2022 03:56 by PCW	Replies:6 Views:964	Last Post by PCW 24 May 2022 03:56
Mesa 7i92 to BOB all home switch Topic started 04 May 2022 13:27, by aabtech Last Post 23 May 2022 14:50 by aabtech	Replies:7 Views:1077	Last Post by aabtech 23 May 2022 14:50
Torch delay / torch height? Topic started 18 May 2022 21:39, by motal2004 Last Post 19 May 2022 23:34 by motal2004	Replies:5 Views:858	motal2004 Last Post by motal2004 19 May 2022 23:34
THC cannot keep up Topic started 28 Apr 2022 19:58, by Jalapeno56 Last Post 17 May 2022 23:55 by Jalapeno56 1 2 3 ... 6	Replies:55 Views:6250	Jalapeno56 Last Post by Jalapeno56 17 May 2022 23:55

Time to create page: 0.222 seconds