Plasmac 722 topics

A place to ask questions about the Plasmac interface

Subject	Replies / Views	Last Post
Using M65 and M64 in pause mode Topic started 22 Mar 2023 09:10, by DmitryKV Last Post 29 Mar 2023 09:57 by DmitryKV	Replies:4 Views:760	DmitryKV Last Post by DmitryKV 29 Mar 2023 09:57
Plasma hole center punch Topic started 27 Mar 2023 14:09, by aabtech Last Post 27 Mar 2023 15:04 by robertspark	Replies:1 Views:780	robertspark Last Post by robertspark 27 Mar 2023 15:04
Problem with displaying the currently executing line. Topic started 16 Mar 2023 08:13, by DmitryKV Last Post 20 Mar 2023 08:45 by DmitryKV	Replies:4 Views:888	DmitryKV Last Post by DmitryKV 20 Mar 2023 08:45
Framing a metric GCode job on an imperial config Topic started 11 Mar 2023 18:26, by Doug @ Design8Studio.com Last Post 16 Mar 2023 01:10 by snowgoer540 1 2 3	Replies:23 Views:2753	Last Post by snowgoer540 16 Mar 2023 01:10
Invalid characters error when trying to use "IF" statement in GCode Topic started 05 Mar 2023 00:36, by xph1l Last Post 07 Mar 2023 22:43 by xph1l	Replies:8 Views:1025	Last Post by xph1l 07 Mar 2023 22:43
Problem after homing. Topic started 22 Feb 2023 08:30, by DmitryKV Last Post 07 Mar 2023 04:59 by DmitryKV	Replies:4 Views:971	DmitryKV Last Post by DmitryKV 07 Mar 2023 04:59
Sheetcam pp for Qtplasmac. Topic started 27 Feb 2023 17:44, by paulsao Last Post 28 Feb 2023 15:44 by paulsao	Replies:2 Views:858	Last Post by paulsao 28 Feb 2023 15:44
Spaceship plasma.. New here Topic started 24 Feb 2023 04:02, by Defab Last Post 24 Feb 2023 06:57 by rodw	Replies:1 Views:724	Last Post by rodw 24 Feb 2023 06:57
Is there a way to disable THC locking? Topic started 21 Feb 2023 22:59, by Sushi Last Post 22 Feb 2023 18:57 by tommylight	Replies:6 Views:896	Last Post by tommylight 22 Feb 2023 18:57
Fusion 360 post processing with the post processor from the sticky thread Topic started 18 Jan 2023 09:47, by Deveraux Last Post 21 Feb 2023 19:39 by paulsao	Replies:5 Views:1776	Last Post by paulsao 21 Feb 2023 19:39
THCAD SETUP Topic started 06 Feb 2023 10:07, by aabtech Last Post 14 Feb 2023 12:33 by tommylight 1 2 3	Replies:21 Views:3182	Last Post by tommylight 14 Feb 2023 12:33
Internationalisation qtplasmac Topic started 11 Feb 2023 14:44, by web123456 Last Post 12 Feb 2023 11:47 by web123456	Replies:4 Views:813	web123456 Last Post by web123456 12 Feb 2023 11:47
Error with T0 M6 (select plasma tool) Topic started 01 Feb 2023 21:33, by edgemir Last Post 03 Feb 2023 17:36 by edgemir	Replies:8 Views:961	edgemir Last Post by edgemir 03 Feb 2023 17:36
Probing/Ohmic faults. Topic started 24 Jan 2023 12:08, by rodw Last Post 28 Jan 2023 11:26 by phillc54 1 2	Replies:13 Views:2284	Last Post by phillc54 28 Jan 2023 11:26
jogging disabled if float switch triggered Topic started 19 Jan 2023 08:28, by rodw Last Post 19 Jan 2023 09:10 by snowgoer540	Replies:5 Views:856	Last Post by snowgoer540 19 Jan 2023 09:10
Enable Auto hole cutting Topic started 18 Jan 2023 23:52, by RobKin Last Post 18 Jan 2023 23:57 by phillc54	Replies:1 Views:619	Last Post by phillc54 18 Jan 2023 23:57
qtplasmac_gcode.py: not found after upgrade Topic started 15 Jan 2023 15:12, by Howlingg Last Post 18 Jan 2023 09:27 by Howlingg	Replies:9 Views:1027	Howlingg Last Post by Howlingg 18 Jan 2023 09:27
THCAD-5 Reading negative Voltages Topic started 10 Jan 2023 21:02, by Deveraux Last Post 17 Jan 2023 08:39 by Deveraux	Replies:6 Views:959	Deveraux Last Post by Deveraux 17 Jan 2023 08:39
Gap cut Topic started 05 Dec 2022 17:37, by paulsao Last Post 05 Jan 2023 23:17 by paulsao	Replies:2 Views:888	Last Post by paulsao 05 Jan 2023 23:17
Penetration Issue Topic started 28 Dec 2022 17:45, by Sushi Last Post 03 Jan 2023 14:18 by tommylight	Replies:2 Views:742	Last Post by tommylight 03 Jan 2023 14:18

Time to create page: 0.183 seconds