Driver Boards 2440 topics

Discussion on add on driver boards

Subject	Replies / Views	Last Post
7i77 and chines servo drive Topic started 08 Oct 2020 12:07, by jazial Last Post 09 Oct 2020 15:28 by Todd Zuercher	Replies:7 Views:1331	Last Post by Todd Zuercher 09 Oct 2020 15:28
Linuxcnc with Teknic SST-1500-UCX Topic started 14 Sep 2020 05:26, by spacemanspiffee Last Post 08 Oct 2020 04:41 by PCW 1 2 3	Replies:28 Views:5139	Last Post by PCW 08 Oct 2020 04:41
Out of my depth: DMM servos Topic started 07 Oct 2020 23:24, by mrwilby Last Post 08 Oct 2020 01:01 by mrwilby	Replies:3 Views:1326	mrwilby Last Post by mrwilby 08 Oct 2020 01:01
How do I install Ethercat on Debian buster with linuxcnc 2.8 Topic started 25 Sep 2020 00:51, by Mduran Last Post 04 Oct 2020 16:54 by tommylight	Replies:1 Views:1272	Last Post by tommylight 04 Oct 2020 16:54
Gecko G320X - Closed Loop - Mesa 7i76E + 7i85 Topic started 29 May 2020 01:26, by hoffb77 Last Post 29 Sep 2020 01:52 by hoffb77 1 2	Replies:10 Views:4073	Last Post by hoffb77 29 Sep 2020 01:52
Need help, Mesa 5125 & 7i76 combo and can't get it to move stepper -resolved Topic started 26 Sep 2020 11:36, by centreline Last Post 26 Sep 2020 17:09 by centreline	Replies:7 Views:4032	centreline Last Post by centreline 26 Sep 2020 17:09
Default Low instead of High on 7i76 GPIO Pin? Topic started 26 Sep 2020 02:23, by jhandel Last Post 26 Sep 2020 15:37 by PCW	Replies:3 Views:1449	Last Post by PCW 26 Sep 2020 15:37
Mesa 7i92 Intermittent Read Errors Topic started 06 Sep 2020 10:14, by turretbuddy2 Last Post 25 Sep 2020 10:03 by turretbuddy2	Replies:6 Views:1668	turretbuddy2 Last Post by turretbuddy2 25 Sep 2020 10:03
Mesa 7i92 help Topic started 23 Sep 2020 14:49, by prochj51 Last Post 23 Sep 2020 16:33 by PCW	Replies:3 Views:2147	Last Post by PCW 23 Sep 2020 16:33
Mesa 7i96 pwm to drive servo Topic started 23 Sep 2020 14:16, by Clive S Last Post 23 Sep 2020 15:10 by PCW	Replies:1 Views:1339	Last Post by PCW 23 Sep 2020 15:10
7i84-via-7i44-via-7i93 Mesa configuration wizard Topic started 19 Aug 2020 21:53, by lrak Last Post 22 Sep 2020 17:52 by lrak 1 2 3	Replies:23 Views:5066	Last Post by lrak 22 Sep 2020 17:52
Go to Stepper Driver Topic started 22 Sep 2020 01:29, by AgentWD40 Last Post 22 Sep 2020 08:29 by rodw	Replies:4 Views:1163	Last Post by rodw 22 Sep 2020 08:29
Change with Mesa ethernet setup Topic started 19 Sep 2020 15:50, by kbec Last Post 21 Sep 2020 13:58 by bevins 1 2	Replies:13 Views:7427	Last Post by bevins 21 Sep 2020 13:58
Generic Zynq or Artix-7 card Topic started 31 Aug 2020 08:26, by sokrates Last Post 21 Sep 2020 08:39 by Donno	Replies:1 Views:2445	Last Post by Donno 21 Sep 2020 08:39
G'day from Australia - Mesa board selection advice. Please help. Topic started 06 Sep 2020 07:34, by harmo Last Post 21 Sep 2020 02:56 by BeagleBrainz 1 2	Replies:18 Views:3947	Last Post by BeagleBrainz 21 Sep 2020 02:56
New 7C80 Install Help Topic started 17 Sep 2020 19:31, by CrashOverride Last Post 19 Sep 2020 17:48 by cakeslob	Replies:8 Views:1753	cakeslob Last Post by cakeslob 19 Sep 2020 17:48
Mesa 5i25/7i76 Stepgens 3 and 4 stopped working Topic started 05 Sep 2020 15:53, by Uthayne Last Post 18 Sep 2020 23:23 by PCW	Replies:5 Views:1468	Last Post by PCW 18 Sep 2020 23:23
Load feedback from drivers and spindle through RS485 Topic started 14 Sep 2020 20:46, by vmihalca Last Post 16 Sep 2020 10:36 by tommylight	Replies:1 Views:1233	Last Post by tommylight 16 Sep 2020 10:36
Servo drive which is better pwm or step dir Topic started 14 Sep 2020 02:36, by Smarttowers Last Post 14 Sep 2020 17:18 by rodw	Replies:8 Views:3026	Last Post by rodw 14 Sep 2020 17:18
Mesa 7I96 setup question Topic started 13 Sep 2020 02:47, by kbec Last Post 13 Sep 2020 08:51 by tommylight	Replies:1 Views:1149	Last Post by tommylight 13 Sep 2020 08:51

Time to create page: 0.515 seconds