Driver Boards 2414 topics

Discussion on add on driver boards

Subject	Replies / Views	Last Post
RS-485 on 5i25+7i76/7i85 Topic started 09 Jan 2020 10:56, by rumking Last Post 20 Oct 2020 18:01 by PCW 1 2 3	Replies:26 Views:6192	Last Post by PCW 20 Oct 2020 18:01
Switch from mach3 & china BoB to Linuxcnc & Mesa Card Combo Topic started 19 Oct 2020 20:16, by Sadmeatball Last Post 20 Oct 2020 06:54 by Sadmeatball	Replies:2 Views:1976	Sadmeatball Last Post by Sadmeatball 20 Oct 2020 06:54
MPG encoder count by 4? Topic started 18 Oct 2020 19:41, by jhandel Last Post 19 Oct 2020 21:11 by rodw 1 2	Replies:18 Views:3271	Last Post by rodw 19 Oct 2020 21:11
MESA recommendation please Topic started 16 Oct 2020 09:40, by whatwasIthinking Last Post 18 Oct 2020 10:57 by tommylight	Replies:3 Views:1332	Last Post by tommylight 18 Oct 2020 10:57
7i76e Bit File Topic started 16 Oct 2020 12:49, by micknucam Last Post 16 Oct 2020 15:06 by micknucam	Replies:2 Views:1176	micknucam Last Post by micknucam 16 Oct 2020 15:06
Troubleshooting USB-RS485 Module Topic started 14 Oct 2020 00:07, by TannerFrisby Last Post 15 Oct 2020 06:23 by rootboy	Replies:5 Views:2637	Last Post by rootboy 15 Oct 2020 06:23
7i92h with 7i77, 7i74,7i71,7i70,7i73 Topic started 03 Oct 2020 13:45, by Thods1222 Last Post 14 Oct 2020 00:27 by Thods1222 1 2	Replies:19 Views:2889	Thods1222 Last Post by Thods1222 14 Oct 2020 00:27
Use 7i76e spindle encoder for MPG or just use 2 digital pins for A/B pulses? Topic started 11 Oct 2020 21:33, by jhandel Last Post 13 Oct 2020 14:01 by PCW	Replies:5 Views:1260	Last Post by PCW 13 Oct 2020 14:01
7i76 spindle control Topic started 29 Sep 2020 08:10, by centreline Last Post 13 Oct 2020 12:35 by summat 1 2	Replies:14 Views:3555	summat Last Post by summat 13 Oct 2020 12:35
7i77 No Encoder Input Topic started 13 Oct 2020 01:22, by Steelman Last Post 13 Oct 2020 01:47 by Steelman	Replies:2 Views:871	Steelman Last Post by Steelman 13 Oct 2020 01:47
Stepgen on remote serial board? (Mesa) Topic started 12 Oct 2020 11:10, by MattyZee Last Post 12 Oct 2020 13:56 by PCW	Replies:1 Views:940	Last Post by PCW 12 Oct 2020 13:56
LinuxCNC installed - Next step? Topic started 12 Oct 2020 13:14, by txtrone Last Post 12 Oct 2020 13:22 by tommylight	Replies:1 Views:866	Last Post by tommylight 12 Oct 2020 13:22
7i77 and chines servo drive Topic started 08 Oct 2020 12:07, by jazial Last Post 09 Oct 2020 15:28 by Todd Zuercher	Replies:7 Views:1207	Last Post by Todd Zuercher 09 Oct 2020 15:28
Linuxcnc with Teknic SST-1500-UCX Topic started 14 Sep 2020 05:26, by spacemanspiffee Last Post 08 Oct 2020 04:41 by PCW 1 2 3	Replies:28 Views:4774	Last Post by PCW 08 Oct 2020 04:41
Out of my depth: DMM servos Topic started 07 Oct 2020 23:24, by mrwilby Last Post 08 Oct 2020 01:01 by mrwilby	Replies:3 Views:1207	mrwilby Last Post by mrwilby 08 Oct 2020 01:01
How do I install Ethercat on Debian buster with linuxcnc 2.8 Topic started 25 Sep 2020 00:51, by Mduran Last Post 04 Oct 2020 16:54 by tommylight	Replies:1 Views:1151	Last Post by tommylight 04 Oct 2020 16:54
Gecko G320X - Closed Loop - Mesa 7i76E + 7i85 Topic started 29 May 2020 01:26, by hoffb77 Last Post 29 Sep 2020 01:52 by hoffb77 1 2	Replies:10 Views:3818	Last Post by hoffb77 29 Sep 2020 01:52
Need help, Mesa 5125 & 7i76 combo and can't get it to move stepper -resolved Topic started 26 Sep 2020 11:36, by centreline Last Post 26 Sep 2020 17:09 by centreline	Replies:7 Views:3754	centreline Last Post by centreline 26 Sep 2020 17:09
Default Low instead of High on 7i76 GPIO Pin? Topic started 26 Sep 2020 02:23, by jhandel Last Post 26 Sep 2020 15:37 by PCW	Replies:3 Views:1297	Last Post by PCW 26 Sep 2020 15:37
Mesa 7i92 Intermittent Read Errors Topic started 06 Sep 2020 10:14, by turretbuddy2 Last Post 25 Sep 2020 10:03 by turretbuddy2	Replies:6 Views:1515	turretbuddy2 Last Post by turretbuddy2 25 Sep 2020 10:03

Time to create page: 0.220 seconds