General LinuxCNC Questions 5931 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
Yaskawa SGDG-04GT torque drives Topic started 09 Nov 2017 01:00, by bevins Last Post 09 Nov 2017 13:31 by andypugh	Replies:2 Views:898	Last Post by andypugh 09 Nov 2017 13:31
Stepconfig test screen Topic started 09 Nov 2017 00:28, by royKO1405 Last Post 09 Nov 2017 00:35 by PCW	Replies:1 Views:862	Last Post by PCW 09 Nov 2017 00:35
5i25 7i77 7i74/7i84, 7i71. Power up issues Topic started 06 Nov 2017 22:39, by bevins Last Post 07 Nov 2017 19:09 by PCW	Replies:5 Views:1151	Last Post by PCW 07 Nov 2017 19:09
Went to start up mill and none of the axis will move? Topic started 04 Nov 2017 21:28, by jamby Last Post 07 Nov 2017 19:07 by PCW 1 2	Replies:19 Views:2451	Last Post by PCW 07 Nov 2017 19:07
Machine Interruption - high speed higher accelation Topic started 26 Oct 2017 19:42, by probamo Last Post 07 Nov 2017 18:54 by probamo	Replies:7 Views:1342	Last Post by probamo 07 Nov 2017 18:54
Using Serial on LinuxCNC Topic started 06 Nov 2017 12:09, by Bello Last Post 07 Nov 2017 08:31 by Bello	Replies:2 Views:4874	Last Post by Bello 07 Nov 2017 08:31
PCI Parport 2 not recognized Topic started 03 Nov 2017 08:27, by Bello Last Post 06 Nov 2017 12:33 by andypugh 1 2	Replies:14 Views:3419	Last Post by andypugh 06 Nov 2017 12:33
Oscillating stepper motors Topic started 31 Oct 2017 21:42, by Muz94 Last Post 03 Nov 2017 18:21 by Muz94	Replies:6 Views:1632	Muz94 Last Post by Muz94 03 Nov 2017 18:21
4 and 5 axis code generator software Topic started 01 Nov 2017 19:20, by grijalvap Last Post 03 Nov 2017 16:28 by andypugh	Replies:1 Views:1241	Last Post by andypugh 03 Nov 2017 16:28
zero return with stepgen 7i76, 7i77, and 7i92 Topic started 24 May 2017 20:54, by Diederik Last Post 03 Nov 2017 06:45 by Diederik 1 2	Replies:10 Views:3443	Last Post by Diederik 03 Nov 2017 06:45
7i77 firmware Topic started 01 Nov 2017 22:04, by Diederik Last Post 02 Nov 2017 04:23 by Diederik	Replies:2 Views:972	Last Post by Diederik 02 Nov 2017 04:23
soft limits different after power cycle Topic started 15 Oct 2017 00:25, by RayJr Last Post 31 Oct 2017 13:22 by andypugh 1 2 3	Replies:25 Views:3651	Last Post by andypugh 31 Oct 2017 13:22
Losing Variable Topic started 28 Oct 2017 10:34, by Nitram Last Post 31 Oct 2017 01:03 by andypugh	Replies:3 Views:1078	Last Post by andypugh 31 Oct 2017 01:03
5i25_7i77_bob.bit required Topic started 28 Oct 2017 05:21, by Diederik Last Post 30 Oct 2017 04:21 by Diederik	Replies:2 Views:1023	Last Post by Diederik 30 Oct 2017 04:21
Errors preventing LinuxCNC from starting. Topic started 07 Sep 2017 19:02, by cncjohn Last Post 29 Oct 2017 03:55 by Todd Zuercher 1 2 3 4	Replies:32 Views:7576	Last Post by Todd Zuercher 29 Oct 2017 03:55
Invalid Security code Topic started 28 Oct 2017 07:32, by Nitram Last Post 29 Oct 2017 01:15 by andypugh	Replies:1 Views:1215	Last Post by andypugh 29 Oct 2017 01:15
Current Feed F-code in Active G Codes Topic started 26 Oct 2017 20:26, by n81641 Last Post 28 Oct 2017 16:49 by n81641	Replies:8 Views:1114	n81641 Last Post by n81641 28 Oct 2017 16:49
Activating air blow valve M6 Topic started 15 Oct 2017 08:38, by lesureia Last Post 28 Oct 2017 07:57 by lesureia 1 2	Replies:17 Views:3468	lesureia Last Post by lesureia 28 Oct 2017 07:57
What i thought was mechanical backlash, is not. Topic started 26 Oct 2017 05:33, by bevins Last Post 27 Oct 2017 15:12 by bevins	Replies:2 Views:1149	Last Post by bevins 27 Oct 2017 15:12
moving the gantry manually Topic started 23 Oct 2017 16:53, by jlroch Last Post 24 Oct 2017 23:37 by andypugh	Replies:2 Views:1174	Last Post by andypugh 24 Oct 2017 23:37

Time to create page: 1.028 seconds