General LinuxCNC Questions 6179 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
Problem when I setup the backlash option Topic started 04 Sep 2022 12:15, by Nest Last Post 06 Sep 2022 20:31 by Nest	Replies:2 Views:920	Last Post by Nest 06 Sep 2022 20:31
random fails on latency tests Topic started 10 Jul 2022 19:54, by tatel Last Post 06 Sep 2022 10:54 by tommylight 1 2	Replies:16 Views:4273	Last Post by tommylight 06 Sep 2022 10:54
ATC Project - Debug phase Topic started 07 Apr 2022 20:17, by spumco Last Post 05 Sep 2022 23:39 by spumco 1 2 3 ... 20	Replies:193 Views:66.2k	spumco Last Post by spumco 05 Sep 2022 23:39
UART controlled stepper drivers and linuxcnc Topic started 19 Aug 2022 16:33, by maarten12100 Last Post 04 Sep 2022 22:04 by maarten12100 1 2	Replies:10 Views:7667	maarten12100 Last Post by maarten12100 04 Sep 2022 22:04
can't get any signals from 7i96s I/O card Topic started 31 Aug 2022 20:45, by Dr. John Last Post 03 Sep 2022 22:33 by rodw 1 2	Replies:10 Views:3363	Last Post by rodw 03 Sep 2022 22:33
G code Ripper Topic started 25 Aug 2022 15:49, by rajsekhar Last Post 03 Sep 2022 20:03 by cmorley	Replies:3 Views:2225	cmorley Last Post by cmorley 03 Sep 2022 20:03
Y-Gantry problems to setup Topic started 25 Aug 2022 20:37, by Onig01 Last Post 03 Sep 2022 19:17 by andypugh	Replies:9 Views:1029	Last Post by andypugh 03 Sep 2022 19:17
Interpolator programmed stops Topic started 24 Aug 2022 08:53, by arabel1a Last Post 03 Sep 2022 19:12 by andypugh	Replies:6 Views:1210	Last Post by andypugh 03 Sep 2022 19:12
Drawing up a wiring diagram Topic started 20 Aug 2022 22:15, by Aldenflorio Last Post 03 Sep 2022 10:17 by andypugh	Replies:3 Views:1442	Last Post by andypugh 03 Sep 2022 10:17
Access to MDI parameters outside linuxcnc Topic started 25 Aug 2022 17:39, by arabel1a Last Post 03 Sep 2022 09:37 by andypugh	Replies:1 Views:1048	Last Post by andypugh 03 Sep 2022 09:37
Parker ac10 vfd control problems Topic started 17 Aug 2022 13:09, by Mart45 Last Post 03 Sep 2022 09:25 by andypugh	Replies:1 Views:966	Last Post by andypugh 03 Sep 2022 09:25
Bottom line on Raspberry pi/Ethenet Mesa FPGA Topic started 27 Aug 2022 11:57, by hhscott Last Post 31 Aug 2022 01:58 by Bari	Replies:6 Views:2891	Last Post by Bari 31 Aug 2022 01:58
Incorrect operation of backlash compensation when going home Topic started 25 Aug 2022 07:04, by tpolimer2000 Last Post 29 Aug 2022 15:28 by tpolimer2000	Replies:7 Views:1719	tpolimer2000 Last Post by tpolimer2000 29 Aug 2022 15:28
Mysterious interaction between running the spindle and the tool length probing c Topic started 27 Aug 2022 03:56, by Jonathan_H Last Post 28 Aug 2022 22:44 by Jonathan_H	Replies:1 Views:791	Jonathan_H Last Post by Jonathan_H 28 Aug 2022 22:44
Attached parallel board to breakout board can't open up linuxcnc anymore Topic started 23 Aug 2022 15:40, by Routerworks Last Post 28 Aug 2022 21:15 by tommylight 1 2 3 4	Replies:33 Views:4613	Last Post by tommylight 28 Aug 2022 21:15
G code from Pen drive Topic started 22 Aug 2022 12:25, by rajsekhar Last Post 28 Aug 2022 00:08 by tatel	Replies:8 Views:1626	tatel Last Post by tatel 28 Aug 2022 00:08
switchkins - using own kinematics module as kinstype=2 Topic started 23 Jul 2022 19:01, by mittim Last Post 27 Aug 2022 15:45 by mittim 1 2	Replies:15 Views:3606	Last Post by mittim 27 Aug 2022 15:45
ohm sensor Topic started 26 Aug 2022 14:53, by chuben Last Post 27 Aug 2022 04:01 by rodw	Replies:2 Views:869	Last Post by rodw 27 Aug 2022 04:01
Subroutine Topic started 26 Aug 2022 14:48, by Shop Dog Last Post 26 Aug 2022 16:14 by Shop Dog	Replies:2 Views:946	Shop Dog Last Post by Shop Dog 26 Aug 2022 16:14
How to read GPIO in real time? Topic started 16 Aug 2022 10:13, by chen1234 Last Post 26 Aug 2022 14:15 by andypugh	Replies:2 Views:1334	Last Post by andypugh 26 Aug 2022 14:15

Time to create page: 0.410 seconds