General LinuxCNC Questions 6777 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
Coordinate system - Running from a program line problem. Topic started 31 Jan 2021 20:03, by AlessandroT Last Post 03 Feb 2021 22:54 by andypugh 1 2	Replies:12 Views:1504	Last Post by andypugh 03 Feb 2021 22:54
Chineese tool setter Manual Topic started 03 Feb 2021 03:14, by Benb Last Post 03 Feb 2021 17:55 by itsme	Replies:2 Views:697	itsme Last Post by itsme 03 Feb 2021 17:55
5v drive enable on mesa board Topic started 17 Jan 2018 22:31, by zmcdona1 Last Post 03 Feb 2021 16:41 by The Feral Engineer 1 2	Replies:15 Views:3656	Last Post by The Feral Engineer 03 Feb 2021 16:41
Changing INI JOINT SCALE online Topic started 31 Jan 2021 17:58, by AlessandroT Last Post 02 Feb 2021 22:25 by PCW 1 2	Replies:17 Views:2330	Last Post by PCW 02 Feb 2021 22:25
G54 Co-ordinate system frozen Topic started 24 Jan 2021 12:46, by IanK Last Post 02 Feb 2021 12:46 by IanK	Replies:5 Views:693	IanK Last Post by IanK 02 Feb 2021 12:46
Just Starting in CNC hobby and looking for SBC advice Topic started 01 Feb 2021 14:27, by Craig E Last Post 01 Feb 2021 21:23 by tommylight	Replies:5 Views:946	Last Post by tommylight 01 Feb 2021 21:23
Problems with HuanYang VFD in 2.7 and limiting switch in 2.8./2.8.1 Topic started 24 Jan 2021 20:26, by hky Last Post 01 Feb 2021 03:26 by hky	Replies:5 Views:703	hky Last Post by hky 01 Feb 2021 03:26
Advice needed. Topic started 01 Feb 2021 00:42, by Dropout Last Post 01 Feb 2021 01:02 by andypugh	Replies:1 Views:543	Last Post by andypugh 01 Feb 2021 01:02
Tandem y axis for plasma table Topic started 12 Sep 2020 04:32, by Electechcans Last Post 31 Jan 2021 02:15 by slukas 1 2 3 ... 5	Replies:49 Views:6134	slukas Last Post by slukas 31 Jan 2021 02:15
Homing, can't figure it out. Topic started 27 Jan 2021 10:19, by SPH Last Post 31 Jan 2021 00:11 by andypugh	Replies:6 Views:668	Last Post by andypugh 31 Jan 2021 00:11
QTDragon - Popup keyboard not working in REF offset popup. Topic started 27 Nov 2020 00:10, by JohnnyCNC Last Post 30 Jan 2021 18:25 by JohnnyCNC	Replies:7 Views:825	Last Post by JohnnyCNC 30 Jan 2021 18:25
Problems with touch off plate configuration Topic started 28 Jan 2021 14:43, by mitakata_net Last Post 30 Jan 2021 12:05 by tommylight 1 2	Replies:12 Views:1892	Last Post by tommylight 30 Jan 2021 12:05
Axis errors out when ran from an RDP session Topic started 25 Apr 2018 04:49, by stioc Last Post 29 Jan 2021 18:53 by rodw	Replies:9 Views:2743	Last Post by rodw 29 Jan 2021 18:53
No 7i92 board found Topic started 28 Jan 2021 14:01, by bevins Last Post 29 Jan 2021 13:04 by bevins	Replies:8 Views:1047	Last Post by bevins 29 Jan 2021 13:04
Mesa 7i76e CR2 red led on at power up Topic started 29 Apr 2019 09:19, by DaveRosario Last Post 29 Jan 2021 00:13 by andypugh 1 2	Replies:12 Views:2557	Last Post by andypugh 29 Jan 2021 00:13
Jog While Paused? Topic started 13 Jan 2021 09:13, by vmihalca Last Post 28 Jan 2021 07:53 by seebaer1976	Replies:5 Views:1195	seebaer1976 Last Post by seebaer1976 28 Jan 2021 07:53
G83 question Topic started 27 Jan 2021 23:00, by acondit Last Post 28 Jan 2021 00:07 by andypugh	Replies:1 Views:747	Last Post by andypugh 28 Jan 2021 00:07
Spindle speed variation on lathe Topic started 27 Jan 2021 15:15, by Catch22 Last Post 27 Jan 2021 23:57 by cmorley	Replies:4 Views:844	cmorley Last Post by cmorley 27 Jan 2021 23:57
Can I use a WCH Parallel Port Card? Topic started 20 Jan 2021 20:23, by mf290997 Last Post 27 Jan 2021 23:03 by mf290997	Replies:7 Views:1009	mf290997 Last Post by mf290997 27 Jan 2021 23:03
Simulation of Mesa config Topic started 27 Nov 2017 17:24, by Mike_Eitel Last Post 27 Jan 2021 10:21 by rodw	Replies:7 Views:1532	Last Post by rodw 27 Jan 2021 10:21

Time to create page: 0.441 seconds