General LinuxCNC Questions 6466 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
Serial communication in linucnc Topic started 11 May 2020 17:43, by aleksamc Last Post 12 May 2020 08:22 by tommylight	Replies:3 Views:933	Last Post by tommylight 12 May 2020 08:22
VELOCITY AXIS RETURN WITH HOME_OFFSET VALUE Topic started 10 May 2020 11:45, by papagno-source Last Post 10 May 2020 11:47 by tommylight	Replies:1 Views:645	Last Post by tommylight 10 May 2020 11:47
Tool Compensation for Hotwire-Machine Topic started 08 May 2020 13:38, by Maltinho Last Post 09 May 2020 06:34 by bbsr_5a	Replies:1 Views:667	bbsr_5a Last Post by bbsr_5a 09 May 2020 06:34
7i77 not detecting all of a sudden Topic started 06 May 2020 01:23, by SPH Last Post 07 May 2020 01:44 by SPH 1 2	Replies:12 Views:1513	Last Post by SPH 07 May 2020 01:44
ac servo moving a bit by hand when enabled Topic started 05 May 2020 23:39, by bevins Last Post 06 May 2020 12:08 by andypugh	Replies:1 Views:630	Last Post by andypugh 06 May 2020 12:08
Limit switches and E-Stop Topic started 30 Apr 2020 11:21, by SPH Last Post 06 May 2020 11:44 by Becksvill	Replies:9 Views:1421	Becksvill Last Post by Becksvill 06 May 2020 11:44
Error on start unexpected realtime delay task 0 or task1 Topic started 05 May 2020 10:46, by gzcwnk Last Post 06 May 2020 06:41 by gzcwnk 1 2	Replies:10 Views:1916	gzcwnk Last Post by gzcwnk 06 May 2020 06:41
parallel port no longer detected by LinuxCNC and neither by dmesg, failed? Topic started 05 May 2020 09:24, by gzcwnk Last Post 06 May 2020 06:28 by gzcwnk 1 2	Replies:11 Views:1600	gzcwnk Last Post by gzcwnk 06 May 2020 06:28
Can I position an axis using the numeric keypad? Topic started 05 May 2020 04:42, by pmconsulting Last Post 06 May 2020 06:01 by cmorley	Replies:3 Views:794	cmorley Last Post by cmorley 06 May 2020 06:01
2.8.0~pre1 python linuxcnc.home(0) not working Topic started 02 May 2020 16:26, by LearningLinuxCNC Last Post 05 May 2020 16:37 by LearningLinuxCNC	Replies:5 Views:1045	Last Post by LearningLinuxCNC 05 May 2020 16:37
Mesa 5i25 supply voltages Topic started 22 Apr 2020 16:46, by Wirewrap Last Post 04 May 2020 19:00 by Wirewrap	Replies:2 Views:756	Last Post by Wirewrap 04 May 2020 19:00
XHC WHB04B-4 pendant Topic started 01 May 2020 16:57, by Catch22 Last Post 02 May 2020 11:15 by rodw	Replies:2 Views:893	Last Post by rodw 02 May 2020 11:15
how configure EMC2 in raspberry pi (GPIO ) Topic started 25 Jun 2014 23:34, by Anis Last Post 02 May 2020 08:34 by bbsr_5a	Replies:4 Views:4751	bbsr_5a Last Post by bbsr_5a 02 May 2020 08:34
Program takes roughly three times longer to run than it should Topic started 29 Apr 2020 23:05, by adouglas89 Last Post 01 May 2020 15:11 by bbsr_5a	Replies:8 Views:823	bbsr_5a Last Post by bbsr_5a 01 May 2020 15:11
Version 2.8 or 2.9? Topic started 01 May 2020 14:04, by Catch22 Last Post 01 May 2020 15:08 by bbsr_5a	Replies:2 Views:934	bbsr_5a Last Post by bbsr_5a 01 May 2020 15:08
proma sd step/dir Topic started 30 Apr 2020 20:36, by getyers Last Post 30 Apr 2020 21:07 by rodw	Replies:2 Views:600	Last Post by rodw 30 Apr 2020 21:07
SOLVED: Trouble getting at the tool table via Python... Topic started 29 Apr 2020 18:40, by pferrick Last Post 30 Apr 2020 05:56 by cmorley	Replies:5 Views:837	cmorley Last Post by cmorley 30 Apr 2020 05:56
z-Clamp setup Topic started 29 Apr 2020 07:10, by bbsr_5a Last Post 29 Apr 2020 18:59 by bbsr_5a	Replies:3 Views:646	bbsr_5a Last Post by bbsr_5a 29 Apr 2020 18:59
Old setup from the ye good olde EMC2-days. Topic started 28 Apr 2020 19:05, by oddname Last Post 28 Apr 2020 19:35 by tommylight	Replies:1 Views:597	Last Post by tommylight 28 Apr 2020 19:35
Limit Switch Troubles - HAL Debounce Topic started 18 Dec 2014 10:43, by ctrl-frq Last Post 28 Apr 2020 18:45 by andypugh 1 2 3 ... 5	Replies:42 Views:13.2k	Last Post by andypugh 28 Apr 2020 18:45

Time to create page: 0.270 seconds