General LinuxCNC Questions 6188 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
eoffset_per_angle opa example Topic started 19 Aug 2020 18:21, by tuxcnc Last Post 19 Aug 2020 20:10 by dgarrett	Replies:1 Views:978	dgarrett Last Post by dgarrett 19 Aug 2020 20:10
How do people "home" or "touch off" Z axis consistently? Topic started 05 Dec 2018 10:38, by uptown47 Last Post 19 Aug 2020 13:00 by wdcnc 1 2	Replies:16 Views:8810	wdcnc Last Post by wdcnc 19 Aug 2020 13:00
Using same key to start cycle and do toolchange Topic started 17 Aug 2020 22:16, by tko829 Last Post 17 Aug 2020 22:16 by tko829	Replies:0 Views:926	tko829 Last Post by tko829 17 Aug 2020 22:16
problem with 5 axis 3 + 2 Topic started 16 Aug 2020 01:06, by el novato Last Post 17 Aug 2020 01:49 by el novato	Replies:4 Views:1107	el novato Last Post by el novato 17 Aug 2020 01:49
Program will not start Topic started 12 Aug 2020 01:00, by allenwg2005 Last Post 16 Aug 2020 17:06 by tommylight	Replies:3 Views:1203	Last Post by tommylight 16 Aug 2020 17:06
Closed Loop stepper Topic started 13 Aug 2020 16:56, by RLA Last Post 15 Aug 2020 11:32 by RLA 1 2 3	Replies:20 Views:8017	RLA Last Post by RLA 15 Aug 2020 11:32
I was told to ask Mesa 5/6i25 questions here. Topic started 05 Apr 2016 17:46, by numbskull Last Post 15 Aug 2020 04:18 by Hamada 1 2	Replies:14 Views:4520	Hamada Last Post by Hamada 15 Aug 2020 04:18
How to configure?: Manual gear change for Closed Loop Lathe Spindle 0-10V Topic started 07 Aug 2020 20:54, by denhen89 Last Post 13 Aug 2020 07:16 by tommylight	Replies:1 Views:1110	Last Post by tommylight 13 Aug 2020 07:16
Controls for Royal Master Centerless grinder Topic started 10 Aug 2020 12:11, by casikora Last Post 13 Aug 2020 07:08 by tommylight	Replies:1 Views:990	Last Post by tommylight 13 Aug 2020 07:08
Setting up Closed loop Spindle speed control and Feedback (0-10V Analog) Topic started 03 Aug 2020 17:27, by denhen89 Last Post 12 Aug 2020 11:21 by RotarySMP 1 2 3	Replies:29 Views:7954	Last Post by RotarySMP 12 Aug 2020 11:21
How to change an Easel file (.nc) to a .ngc file? Topic started 11 Aug 2020 13:14, by woyz8888 Last Post 12 Aug 2020 06:26 by tommylight	Replies:8 Views:4117	Last Post by tommylight 12 Aug 2020 06:26
Can't get my spindle to turn on Topic started 05 Aug 2020 05:49, by devinw Last Post 11 Aug 2020 23:53 by devinw 1 2	Replies:17 Views:3556	devinw Last Post by devinw 11 Aug 2020 23:53
Change Spindle increment on main screen. Topic started 20 May 2020 19:38, by Marcodi Last Post 11 Aug 2020 12:51 by andypugh	Replies:4 Views:1398	Last Post by andypugh 11 Aug 2020 12:51
Stepgen table mode adding one extra state and not following the table properly Topic started 03 Aug 2020 01:27, by nick-parker Last Post 10 Aug 2020 04:46 by nick-parker	Replies:5 Views:1130	nick-parker Last Post by nick-parker 10 Aug 2020 04:46
LinuxCNC for automation Topic started 28 Jul 2020 08:29, by tdon Last Post 09 Aug 2020 19:56 by Grotius 1 2	Replies:14 Views:4536	Last Post by Grotius 09 Aug 2020 19:56
MATRIX_KB in 2.8.0 Topic started 08 Aug 2020 19:18, by Daniel_D_Punkt Last Post 09 Aug 2020 18:09 by Daniel_D_Punkt 1 2	Replies:15 Views:2867	Daniel_D_Punkt Last Post by Daniel_D_Punkt 09 Aug 2020 18:09
Gecko 540 interface Topic started 08 Aug 2020 20:02, by Jwc7992 Last Post 09 Aug 2020 08:22 by tommylight	Replies:3 Views:1041	Last Post by tommylight 09 Aug 2020 08:22
Cannot get M6 ngc remap working Topic started 06 Aug 2020 12:18, by bevins Last Post 07 Aug 2020 22:23 by tommylight 1 2 3	Replies:23 Views:3918	Last Post by tommylight 07 Aug 2020 22:23
xhc-hb04 homing problem Topic started 04 Aug 2020 10:25, by ericg Last Post 06 Aug 2020 03:52 by ericg	Replies:8 Views:1155	ericg Last Post by ericg 06 Aug 2020 03:52
Reading dxf with variable z depth Topic started 04 Aug 2020 22:14, by Iandrinky Last Post 05 Aug 2020 12:06 by andypugh	Replies:3 Views:1133	Last Post by andypugh 05 Aug 2020 12:06

Time to create page: 0.438 seconds