General LinuxCNC Questions 6769 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
How do I setup a 5 axis mill? Topic started 08 Apr 2016 16:46, by Louis Last Post 08 Nov 2019 11:50 by andypugh 1 2 3	Replies:21 Views:17.2k	Last Post by andypugh 08 Nov 2019 11:50
Settings for Homing Topic started 06 Nov 2019 14:32, by ytiuqibu Last Post 07 Nov 2019 19:43 by ytiuqibu	Replies:5 Views:2030	ytiuqibu Last Post by ytiuqibu 07 Nov 2019 19:43
Lathe Z axis/joint not homing after updating to 2.8 Topic started 22 May 2019 20:20, by vmihalca Last Post 07 Nov 2019 11:33 by andypugh 1 2 3	Replies:22 Views:3093	Last Post by andypugh 07 Nov 2019 11:33
How to zero coordinates? Topic started 07 Nov 2019 01:26, by Cranktown Last Post 07 Nov 2019 06:44 by rodw 1 2	Replies:10 Views:2251	Last Post by rodw 07 Nov 2019 06:44
Soemething a little different Topic started 04 Nov 2019 22:08, by An Last Post 06 Nov 2019 21:35 by andypugh	Replies:5 Views:785	Last Post by andypugh 06 Nov 2019 21:35
Nube here Topic started 06 Nov 2019 07:36, by Laser Nube Last Post 06 Nov 2019 14:49 by andypugh	Replies:2 Views:659	Last Post by andypugh 06 Nov 2019 14:49
dmesg > hm.txt Produces An Empty File Topic started 05 Nov 2019 20:42, by BigBird Last Post 05 Nov 2019 23:05 by PCW	Replies:3 Views:864	Last Post by PCW 05 Nov 2019 23:05
Run From Here with LinuxCNC Topic started 04 Nov 2019 17:48, by Vmax549 Last Post 05 Nov 2019 18:47 by Vmax549	Replies:3 Views:846	Vmax549 Last Post by Vmax549 05 Nov 2019 18:47
Speed vs microsteps Topic started 02 Nov 2019 15:47, by Leon82 Last Post 03 Nov 2019 03:56 by Leon82	Replies:6 Views:871	Leon82 Last Post by Leon82 03 Nov 2019 03:56
Thank you letter Topic started 30 Oct 2019 05:52, by cheng Last Post 03 Nov 2019 03:40 by Dinuka_Shehan	Replies:4 Views:826	Last Post by Dinuka_Shehan 03 Nov 2019 03:40
intergrate computed torque control (dynamic control) for linuxcnc Topic started 30 Sep 2017 16:24, by thang Last Post 02 Nov 2019 07:16 by thang 1 2 3	Replies:20 Views:3862	thang Last Post by thang 02 Nov 2019 07:16
issue with "home all" after power failure Topic started 01 Nov 2019 18:01, by jamby Last Post 01 Nov 2019 19:29 by jamby	Replies:2 Views:662	jamby Last Post by jamby 01 Nov 2019 19:29
Recompiling installed-from-USB (Debian based) LinuxCNC Topic started 30 Oct 2019 10:15, by ross_dev Last Post 01 Nov 2019 13:42 by andypugh	Replies:6 Views:773	Last Post by andypugh 01 Nov 2019 13:42
Gmoccapy: no audio available Topic started 31 Oct 2019 23:16, by DaveRosario Last Post 01 Nov 2019 00:22 by DaveRosario	Replies:2 Views:908	Last Post by DaveRosario 01 Nov 2019 00:22
Need clarification on hooking up this driver Topic started 27 Oct 2019 17:03, by Leon82 Last Post 29 Oct 2019 10:35 by Leon82	Replies:6 Views:780	Leon82 Last Post by Leon82 29 Oct 2019 10:35
Driver timing for Longs motors DM860a Topic started 19 Oct 2019 22:40, by freddie Last Post 29 Oct 2019 10:11 by andypugh	Replies:8 Views:1560	Last Post by andypugh 29 Oct 2019 10:11
Some questions about oyostepper Topic started 28 Oct 2019 07:39, by unlessou32 Last Post 28 Oct 2019 08:35 by pl7i92	Replies:1 Views:750	Last Post by pl7i92 28 Oct 2019 08:35
7i92 setup help Topic started 29 Oct 2016 02:02, by dingbatca Last Post 28 Oct 2019 07:37 by unlessou32 1 2	Replies:12 Views:8290	Last Post by unlessou32 28 Oct 2019 07:37
mesa 7i84 Topic started 25 Oct 2019 12:47, by viski Last Post 25 Oct 2019 13:01 by viski	Replies:2 Views:708	viski Last Post by viski 25 Oct 2019 13:01
Breakout boards problem Topic started 18 Oct 2019 09:12, by aaron Last Post 25 Oct 2019 06:52 by pl7i92 1 2	Replies:14 Views:2705	Last Post by pl7i92 25 Oct 2019 06:52

Time to create page: 0.291 seconds