Driver Boards 2656 topics

Discussion on add on driver boards

Subject	Replies / Views	Last Post
Troubleshooting USB-RS485 Module Topic started 14 Oct 2020 00:07, by TannerFrisby Last Post 15 Oct 2020 06:23 by rootboy	Replies:5 Views:1744	Last Post by rootboy 15 Oct 2020 06:23
7i92h with 7i77, 7i74,7i71,7i70,7i73 Topic started 03 Oct 2020 13:45, by Thods1222 Last Post 14 Oct 2020 00:27 by Thods1222 1 2	Replies:19 Views:2344	Thods1222 Last Post by Thods1222 14 Oct 2020 00:27
Use 7i76e spindle encoder for MPG or just use 2 digital pins for A/B pulses? Topic started 11 Oct 2020 21:33, by jhandel Last Post 13 Oct 2020 14:01 by PCW	Replies:5 Views:1022	Last Post by PCW 13 Oct 2020 14:01
7i76 spindle control Topic started 29 Sep 2020 08:10, by centreline Last Post 13 Oct 2020 12:35 by summat 1 2	Replies:14 Views:2884	summat Last Post by summat 13 Oct 2020 12:35
7i77 No Encoder Input Topic started 13 Oct 2020 01:22, by Steelman Last Post 13 Oct 2020 01:47 by Steelman	Replies:2 Views:671	Steelman Last Post by Steelman 13 Oct 2020 01:47
Stepgen on remote serial board? (Mesa) Topic started 12 Oct 2020 11:10, by MattyZee Last Post 12 Oct 2020 13:56 by PCW	Replies:1 Views:702	Last Post by PCW 12 Oct 2020 13:56
LinuxCNC installed - Next step? Topic started 12 Oct 2020 13:14, by txtrone Last Post 12 Oct 2020 13:22 by tommylight	Replies:1 Views:665	Last Post by tommylight 12 Oct 2020 13:22
7i77 and chines servo drive Topic started 08 Oct 2020 12:07, by jazial Last Post 09 Oct 2020 15:28 by Todd Zuercher	Replies:7 Views:962	Last Post by Todd Zuercher 09 Oct 2020 15:28
Linuxcnc with Teknic SST-1500-UCX Topic started 14 Sep 2020 05:26, by spacemanspiffee Last Post 08 Oct 2020 04:41 by PCW 1 2 3	Replies:28 Views:3805	Last Post by PCW 08 Oct 2020 04:41
Out of my depth: DMM servos Topic started 07 Oct 2020 23:24, by mrwilby Last Post 08 Oct 2020 01:01 by mrwilby	Replies:3 Views:974	mrwilby Last Post by mrwilby 08 Oct 2020 01:01
How do I install Ethercat on Debian buster with linuxcnc 2.8 Topic started 25 Sep 2020 00:51, by Mduran Last Post 04 Oct 2020 16:54 by tommylight	Replies:1 Views:900	Last Post by tommylight 04 Oct 2020 16:54
Gecko G320X - Closed Loop - Mesa 7i76E + 7i85 Topic started 29 May 2020 01:26, by hoffb77 Last Post 29 Sep 2020 01:52 by hoffb77 1 2	Replies:10 Views:3049	Last Post by hoffb77 29 Sep 2020 01:52
Need help, Mesa 5125 & 7i76 combo and can't get it to move stepper -resolved Topic started 26 Sep 2020 11:36, by centreline Last Post 26 Sep 2020 17:09 by centreline	Replies:7 Views:2981	centreline Last Post by centreline 26 Sep 2020 17:09
Default Low instead of High on 7i76 GPIO Pin? Topic started 26 Sep 2020 02:23, by jhandel Last Post 26 Sep 2020 15:37 by PCW	Replies:3 Views:974	Last Post by PCW 26 Sep 2020 15:37
Mesa 7i92 Intermittent Read Errors Topic started 06 Sep 2020 10:14, by turretbuddy2 Last Post 25 Sep 2020 10:03 by turretbuddy2	Replies:6 Views:1207	turretbuddy2 Last Post by turretbuddy2 25 Sep 2020 10:03
Mesa 7i92 help Topic started 23 Sep 2020 14:49, by prochj51 Last Post 23 Sep 2020 16:33 by PCW	Replies:3 Views:1238	Last Post by PCW 23 Sep 2020 16:33
Mesa 7i96 pwm to drive servo Topic started 23 Sep 2020 14:16, by Clive S Last Post 23 Sep 2020 15:10 by PCW	Replies:1 Views:915	Last Post by PCW 23 Sep 2020 15:10
7i84-via-7i44-via-7i93 Mesa configuration wizard Topic started 19 Aug 2020 21:53, by lrak Last Post 22 Sep 2020 17:52 by lrak 1 2 3	Replies:23 Views:3675	Last Post by lrak 22 Sep 2020 17:52
Go to Stepper Driver Topic started 22 Sep 2020 01:29, by AgentWD40 Last Post 22 Sep 2020 08:29 by rodw	Replies:4 Views:811	Last Post by rodw 22 Sep 2020 08:29
Change with Mesa ethernet setup Topic started 19 Sep 2020 15:50, by kbec Last Post 21 Sep 2020 13:58 by bevins 1 2	Replies:13 Views:5627	Last Post by bevins 21 Sep 2020 13:58

Time to create page: 0.884 seconds