General LinuxCNC Questions 6007 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
Mesa 7i76eu gpio pins not working Topic started 12 Aug 2025 07:41, by LeonDolnicar Last Post 13 Aug 2025 11:08 by LeonDolnicar	Replies:4 Views:372	LeonDolnicar Last Post by LeonDolnicar 13 Aug 2025 11:08
view > mm vs inches, and tool size display, in AXIS Topic started 11 Aug 2025 03:36, by johnbump Last Post 12 Aug 2025 00:32 by johnbump	Replies:2 Views:269	johnbump Last Post by johnbump 12 Aug 2025 00:32
Hardware requirement if a MESA 7i97T card is used Topic started 11 Aug 2025 15:29, by Hartwig Last Post 11 Aug 2025 15:38 by tommylight	Replies:1 Views:290	Last Post by tommylight 11 Aug 2025 15:38
Diving deeper into linuxcnc Topic started 11 Aug 2025 02:43, by arijitdutta Last Post 11 Aug 2025 12:07 by rodw	Replies:1 Views:287	Last Post by rodw 11 Aug 2025 12:07
LinuxCNC vs Commercial Topic started 18 Mar 2015 05:42, by DuNuNuBatman Last Post 10 Aug 2025 20:18 by tommylight 1 2	Replies:15 Views:10.1k	Last Post by tommylight 10 Aug 2025 20:18
GOG53Z0 Topic started 09 Aug 2025 16:09, by bridges67 Last Post 09 Aug 2025 16:33 by MaHa	Replies:1 Views:232	MaHa Last Post by MaHa 09 Aug 2025 16:33
injection mold machine custom gui Topic started 08 Aug 2025 11:08, by Philip Lydin Last Post 08 Aug 2025 22:58 by andypugh	Replies:4 Views:387	Last Post by andypugh 08 Aug 2025 22:58
Bit length checking on top datum Topic started 04 Aug 2025 14:29, by dannym Last Post 08 Aug 2025 19:56 by andypugh	Replies:4 Views:473	Last Post by andypugh 08 Aug 2025 19:56
6i25 encoder not working right. Topic started 07 Aug 2025 07:03, by Kieran Last Post 07 Aug 2025 08:07 by Kieran	Replies:1 Views:329	Kieran Last Post by Kieran 07 Aug 2025 08:07
Calibration issue Topic started 05 Aug 2025 15:04, by RLA Last Post 06 Aug 2025 20:48 by RLA	Replies:6 Views:413	RLA Last Post by RLA 06 Aug 2025 20:48
prevent jog limit error Topic started 04 Aug 2025 13:50, by konrad Last Post 06 Aug 2025 14:53 by konrad	Replies:7 Views:448	konrad Last Post by konrad 06 Aug 2025 14:53
Is my wire diagram correct? Topic started 28 Mar 2021 18:07, by Haugud Last Post 04 Aug 2025 20:44 by PCW 1 2	Replies:14 Views:6190	Last Post by PCW 04 Aug 2025 20:44
Motion Jitter with LinuxCNC + EtherCAT Topic started 31 Jul 2025 12:14, by Abdulkareem Last Post 04 Aug 2025 09:17 by Abdulkareem	Replies:7 Views:691	Abdulkareem Last Post by Abdulkareem 04 Aug 2025 09:17
Auto mode, reaching first point of coord then "reading" state, no movement Topic started 26 Jul 2025 06:54, by _skinner Last Post 03 Aug 2025 19:54 by andypugh	Replies:4 Views:351	Last Post by andypugh 03 Aug 2025 19:54
Axis and tool length sensor troubles Topic started 14 Jul 2025 14:23, by seuchato Last Post 02 Aug 2025 13:01 by seuchato	Replies:4 Views:504	seuchato Last Post by seuchato 02 Aug 2025 13:01
7i37-COM Topic started 30 Jul 2025 09:07, by ChironFZ16 Last Post 31 Jul 2025 12:44 by PCW	Replies:2 Views:300	Last Post by PCW 31 Jul 2025 12:44
Problem setting up with inputs on 7i96s. Potential Electrical cabinet problem Topic started 30 Jul 2025 18:21, by xlordofpainx Last Post 31 Jul 2025 11:16 by xlordofpainx	Replies:2 Views:355	xlordofpainx Last Post by xlordofpainx 31 Jul 2025 11:16
qtvcp Topic started 30 Jul 2025 05:28, by miha92768 Last Post 30 Jul 2025 13:02 by cmorley	Replies:1 Views:312	cmorley Last Post by cmorley 30 Jul 2025 13:02
Help : Layman configuration for Raspberry Pi 5, Linuxcnc 2.9. and Mesa 7i96 Topic started 28 Jul 2025 09:26, by sk_linuxcnc Last Post 29 Jul 2025 08:32 by sk_linuxcnc 1 2	Replies:16 Views:1672	sk_linuxcnc Last Post by sk_linuxcnc 29 Jul 2025 08:32
problem with num_extrajoint Topic started 26 Jul 2025 23:18, by Thayloreing Last Post 27 Jul 2025 16:55 by andypugh	Replies:6 Views:377	Last Post by andypugh 27 Jul 2025 16:55

Time to create page: 1.183 seconds