Plasmac 629 topics

A place to ask questions about the Plasmac interface

Subject	Replies / Views	Last Post
qtplasmac 2.10 arc ok, thcad thc, and Thcad Ohmic troubleshooting help needed. Topic started 14 Feb 2023 22:56, by jimmyrig Last Post 28 Feb 2023 09:29 by snowgoer540 1 2 3 ... 5	Replies:44 Views:3475	Last Post by snowgoer540 28 Feb 2023 09:29
Spaceship plasma.. New here Topic started 24 Feb 2023 04:02, by Defab Last Post 24 Feb 2023 06:57 by rodw	Replies:1 Views:383	Last Post by rodw 24 Feb 2023 06:57
Is there a way to disable THC locking? Topic started 21 Feb 2023 22:59, by Sushi Last Post 22 Feb 2023 18:57 by tommylight	Replies:6 Views:519	Last Post by tommylight 22 Feb 2023 18:57
Fusion 360 post processing with the post processor from the sticky thread Topic started 18 Jan 2023 09:47, by Deveraux Last Post 21 Feb 2023 19:39 by paulsao	Replies:5 Views:969	Last Post by paulsao 21 Feb 2023 19:39
THCAD SETUP Topic started 06 Feb 2023 10:07, by aabtech Last Post 14 Feb 2023 12:33 by tommylight 1 2 3	Replies:21 Views:1772	Last Post by tommylight 14 Feb 2023 12:33
Internationalisation qtplasmac Topic started 11 Feb 2023 14:44, by web123456 Last Post 12 Feb 2023 11:47 by web123456	Replies:4 Views:480	web123456 Last Post by web123456 12 Feb 2023 11:47
Error with T0 M6 (select plasma tool) Topic started 01 Feb 2023 21:33, by edgemir Last Post 03 Feb 2023 17:36 by edgemir	Replies:8 Views:610	edgemir Last Post by edgemir 03 Feb 2023 17:36
Probing/Ohmic faults. Topic started 24 Jan 2023 12:08, by rodw Last Post 28 Jan 2023 11:26 by phillc54 1 2	Replies:13 Views:1301	Last Post by phillc54 28 Jan 2023 11:26
jogging disabled if float switch triggered Topic started 19 Jan 2023 08:28, by rodw Last Post 19 Jan 2023 09:10 by snowgoer540	Replies:5 Views:449	Last Post by snowgoer540 19 Jan 2023 09:10
Enable Auto hole cutting Topic started 18 Jan 2023 23:52, by RobKin Last Post 18 Jan 2023 23:57 by phillc54	Replies:1 Views:356	Last Post by phillc54 18 Jan 2023 23:57
qtplasmac_gcode.py: not found after upgrade Topic started 15 Jan 2023 15:12, by Howlingg Last Post 18 Jan 2023 09:27 by Howlingg	Replies:9 Views:683	Howlingg Last Post by Howlingg 18 Jan 2023 09:27
THCAD-5 Reading negative Voltages Topic started 10 Jan 2023 21:02, by Deveraux Last Post 17 Jan 2023 08:39 by Deveraux	Replies:6 Views:543	Deveraux Last Post by Deveraux 17 Jan 2023 08:39
Gap cut Topic started 05 Dec 2022 17:37, by paulsao Last Post 05 Jan 2023 23:17 by paulsao	Replies:2 Views:585	Last Post by paulsao 05 Jan 2023 23:17
Penetration Issue Topic started 28 Dec 2022 17:45, by Sushi Last Post 03 Jan 2023 14:18 by tommylight	Replies:2 Views:468	Last Post by tommylight 03 Jan 2023 14:18
QTPlasmaC - Skipping Probing Topic started 21 Dec 2022 14:58, by Sushi Last Post 27 Dec 2022 09:22 by billykid 1 2 3 4	Replies:33 Views:2711	Last Post by billykid 27 Dec 2022 09:22
QTPlasmaC - How to enable FULL THC? Topic started 21 Dec 2022 15:05, by Sushi Last Post 24 Dec 2022 12:15 by tommylight 1 2	Replies:14 Views:1495	Last Post by tommylight 24 Dec 2022 12:15
Backup / Restore Topic started 20 Dec 2022 21:50, by Howlingg Last Post 20 Dec 2022 23:07 by phillc54	Replies:1 Views:427	Last Post by phillc54 20 Dec 2022 23:07
QtPlasmaC Qtvcp Python Traceback on Run From Line after M67 Topic started 20 Dec 2022 01:59, by caretech Last Post 20 Dec 2022 16:06 by snowgoer540	Replies:9 Views:735	Last Post by snowgoer540 20 Dec 2022 16:06
qtplasmac lost arc = turn off and on again? Topic started 14 Dec 2022 13:18, by Mud Last Post 16 Dec 2022 13:34 by snowgoer540	Replies:7 Views:564	Last Post by snowgoer540 16 Dec 2022 13:34
error on closing QTPlasmaC Topic started 13 Dec 2022 21:32, by acourtjester Last Post 14 Dec 2022 03:28 by phillc54	Replies:4 Views:486	Last Post by phillc54 14 Dec 2022 03:28

Time to create page: 0.111 seconds