Plasmac 667 topics

A place to ask questions about the Plasmac interface

Subject	Replies / Views	Last Post
THCAD-10 and voltaje divider ratio. Topic started 26 Aug 2021 22:52, by paulsao Last Post 12 Sep 2021 11:14 by rodw	Replies:8 Views:1301	Last Post by rodw 12 Sep 2021 11:14
Choosing a compressor for plasma cutting Topic started 09 Sep 2020 15:09, by tommylight Last Post 07 Sep 2021 19:56 by billykid 1 2	Replies:14 Views:4588	Last Post by billykid 07 Sep 2021 19:56
QtPlasmaC Jogging Lag Topic started 02 Sep 2021 16:32, by Uthayne Last Post 07 Sep 2021 13:20 by Uthayne 1 2 3 4	Replies:32 Views:3119	Uthayne Last Post by Uthayne 07 Sep 2021 13:20
PlasmaC Will Not Activate Torch Pin on My 7i96 Topic started 24 Sep 2019 02:47, by MakingStuff Last Post 05 Sep 2021 02:40 by pkasy 1 2 3	Replies:25 Views:3208	Last Post by pkasy 05 Sep 2021 02:40
QTvcp ERROR! Message # 1 Topic started 02 Sep 2021 07:38, by danilom Last Post 02 Sep 2021 07:50 by phillc54	Replies:1 Views:660	Last Post by phillc54 02 Sep 2021 07:50
Which THCAD to use for Plasma cutter without voltage divider Topic started 10 Jun 2021 20:55, by alchemy Last Post 31 Aug 2021 11:34 by tommylight 1 2	Replies:12 Views:2518	Last Post by tommylight 31 Aug 2021 11:34
wrong scale thc of the z axis during cutting on qtplasmac Topic started 06 Jul 2021 12:17, by sibista Last Post 27 Aug 2021 12:36 by sibista 1 2 3 ... 10	Replies:94 Views:9075	sibista Last Post by sibista 27 Aug 2021 12:36
QTPlasmaC, first cut ever. What to do after "initial setup"? Topic started 23 Aug 2021 19:21, by fernandosf Last Post 26 Aug 2021 23:03 by phillc54 1 2 3	Replies:20 Views:3191	Last Post by phillc54 26 Aug 2021 23:03
Fusión 360 and Plasmac Topic started 24 Aug 2021 22:08, by paulsao Last Post 25 Aug 2021 14:16 by paulsao	Replies:7 Views:803	Last Post by paulsao 25 Aug 2021 14:16
Showing G53 coordinates Topic started 20 Aug 2021 18:39, by fernandosf Last Post 23 Aug 2021 12:29 by beefy 1 2 3	Replies:21 Views:2816	beefy Last Post by beefy 23 Aug 2021 12:29
Ignore probe during cut Topic started 17 Aug 2021 15:46, by mariusl Last Post 18 Aug 2021 06:43 by mariusl	Replies:8 Views:1260	Last Post by mariusl 18 Aug 2021 06:43
PnCConf Wizard doesn't launch Topic started 09 Aug 2021 01:34, by CFE Last Post 15 Aug 2021 15:58 by crowloy 1 2	Replies:19 Views:1873	crowloy Last Post by crowloy 15 Aug 2021 15:58
QTPlasmaC Z axis "following error" (but it works in AXIS) Topic started 12 Aug 2021 12:28, by fernandosf Last Post 14 Aug 2021 20:36 by fernandosf	Replies:7 Views:903	Last Post by fernandosf 14 Aug 2021 20:36
Camera For Touchoff Topic started 17 Sep 2020 05:46, by phillc54 Last Post 08 Aug 2021 08:47 by partec 1 2 3 ... 7	Replies:60 Views:10.9k	partec Last Post by partec 08 Aug 2021 08:47
ohm sensor Topic started 04 Aug 2021 11:28, by chuben Last Post 05 Aug 2021 14:49 by chuben	Replies:2 Views:639	chuben Last Post by chuben 05 Aug 2021 14:49
qtplasmac error message Topic started 02 Aug 2021 16:22, by crowloy Last Post 04 Aug 2021 09:41 by phillc54	Replies:6 Views:811	Last Post by phillc54 04 Aug 2021 09:41
QTPlasmc GUI questions Topic started 01 Aug 2021 13:20, by robertspark Last Post 02 Aug 2021 13:06 by cmorley	Replies:6 Views:752	cmorley Last Post by cmorley 02 Aug 2021 13:06
QTPlasmac and estop-latch broken (no iocontrol.0.user-request-enable) Topic started 23 Jul 2021 01:02, by rodw Last Post 27 Jul 2021 03:24 by cmorley 1 2 3	Replies:20 Views:2616	cmorley Last Post by cmorley 27 Jul 2021 03:24
postprocessor for plasmaC Topic started 22 Jul 2021 19:07, by shpatb Last Post 25 Jul 2021 20:42 by shpatb	Replies:2 Views:1056	Last Post by shpatb 25 Jul 2021 20:42
Why is Plasmac and QTplasmac pausing at the end of a cut for no reason? Topic started 10 Jun 2021 08:27, by rodw Last Post 23 Jul 2021 10:52 by phillc54 1 2 3 ... 10	Replies:93 Views:8669	Last Post by phillc54 23 Jul 2021 10:52

Time to create page: 0.146 seconds