Plasmac 735 topics

A place to ask questions about the Plasmac interface

Subject	Replies / Views	Last Post
Valid arc lost & top limit is reached while THC moving up Topic started 21 Feb 2022 14:23, by sharp_reaper Last Post 15 Mar 2022 12:50 by sharp_reaper 1 2 3 4	Replies:39 Views:5442	sharp_reaper Last Post by sharp_reaper 15 Mar 2022 12:50
docs minor correction / check Topic started 12 Mar 2022 12:12, by robertspark Last Post 12 Mar 2022 12:46 by snowgoer540	Replies:1 Views:767	Last Post by snowgoer540 12 Mar 2022 12:46
THCAD-300 FOR BOB Topic started 03 Mar 2022 15:58, by aabtech Last Post 04 Mar 2022 09:29 by aabtech	Replies:3 Views:1057	Last Post by aabtech 04 Mar 2022 09:29
Hole cut and fusión 360 Topic started 04 Mar 2022 04:12, by paulsao Last Post 04 Mar 2022 04:12 by paulsao	Replies:0 Views:857	Last Post by paulsao 04 Mar 2022 04:12
Slow My Z Axis Down (losing steps) -Mesa 7i96 Topic started 02 Mar 2022 21:58, by Nick7251 Last Post 03 Mar 2022 20:33 by rodw	Replies:6 Views:965	Last Post by rodw 03 Mar 2022 20:33
Qtvcp Topic started 27 Feb 2022 08:46, by aabtech Last Post 02 Mar 2022 20:48 by aabtech	Replies:7 Views:1398	Last Post by aabtech 02 Mar 2022 20:48
THC for Hypertherm 45XP based on DT-115 / LM393 comparator Topic started 16 Oct 2020 14:08, by radek_marko Last Post 21 Feb 2022 08:49 by Lilow 1 2 3 4	Replies:30 Views:6322	Lilow Last Post by Lilow 21 Feb 2022 08:49
PlasmaC THCAD-10 Topic started 10 Feb 2022 03:05, by Aldenflorio Last Post 20 Feb 2022 00:44 by phillc54 1 2	Replies:18 Views:3349	Last Post by phillc54 20 Feb 2022 00:44
QtPlasmaC backplot for previous cuts Topic started 07 Feb 2022 19:42, by Howlingg Last Post 07 Feb 2022 22:41 by phillc54	Replies:1 Views:903	Last Post by phillc54 07 Feb 2022 22:41
Float switch on 7i96 Topic started 07 Feb 2022 02:10, by salem747 Last Post 07 Feb 2022 19:27 by PCW	Replies:4 Views:1162	Last Post by PCW 07 Feb 2022 19:27
7i96 Configuration Problems Topic started 08 Dec 2021 19:56, by salem747 Last Post 07 Feb 2022 18:06 by PCW 1 2 3 ... 5	Replies:40 Views:6200	Last Post by PCW 07 Feb 2022 18:06
Debounce Topic started 06 Feb 2022 18:09, by salem747 Last Post 07 Feb 2022 11:40 by rodw	Replies:1 Views:1075	Last Post by rodw 07 Feb 2022 11:40
Voltage Scale and Auto Volts Topic started 12 Dec 2021 22:49, by CFE Last Post 07 Feb 2022 02:08 by CFE 1 2 3 ... 5	Replies:46 Views:8166	CFE Last Post by CFE 07 Feb 2022 02:08
Cannot get coefficient for plasmac (THCAD 10) Topic started 03 Feb 2022 05:38, by ML Last Post 03 Feb 2022 10:58 by snowgoer540	Replies:1 Views:928	Last Post by snowgoer540 03 Feb 2022 10:58
Help configuring a Pendant Topic started 24 Dec 2021 22:32, by Jflesburg Last Post 30 Jan 2022 05:25 by cmorley 1 2	Replies:14 Views:3492	cmorley Last Post by cmorley 30 Jan 2022 05:25
ERROR: pierce height would exceed Z axis maximum limit Topic started 28 Jan 2022 01:05, by rodw Last Post 28 Jan 2022 02:31 by snowgoer540	Replies:4 Views:1275	Last Post by snowgoer540 28 Jan 2022 02:31
PC & OpenGL requirements for QTPlasmaC Topic started 21 Mar 2021 00:31, by beefy Last Post 28 Jan 2022 02:08 by kramerda	Replies:4 Views:1368	kramerda Last Post by kramerda 28 Jan 2022 02:08
cut recovery ext pin Topic started 18 Jan 2022 09:39, by billykid Last Post 24 Jan 2022 01:26 by phillc54 1 2	Replies:12 Views:2574	Last Post by phillc54 24 Jan 2022 01:26
Two threads???? Topic started 19 Jan 2022 03:32, by rodw Last Post 19 Jan 2022 09:44 by tommylight	Replies:2 Views:918	Last Post by tommylight 19 Jan 2022 09:44
External THC (mode 2) Ignore ARC OK at start for 1 sec Topic started 17 Jan 2022 13:39, by fernandosf Last Post 18 Jan 2022 07:22 by rodw	Replies:3 Views:1083	Last Post by rodw 18 Jan 2022 07:22

Time to create page: 0.255 seconds