Plasmac 726 topics

A place to ask questions about the Plasmac interface

Subject	Replies / Views	Last Post
Converting over to Raspberry pi4B Topic started 31 Jul 2020 23:35, by kramerda Last Post 01 Aug 2020 01:51 by kramerda	Replies:2 Views:843	kramerda Last Post by kramerda 01 Aug 2020 01:51
PID tuning the THC Topic started 30 Jul 2020 01:10, by snowgoer540 Last Post 31 Jul 2020 07:22 by rodw	Replies:6 Views:1186	Last Post by rodw 31 Jul 2020 07:22
Error opening Linuxcnc/Plasmac after update and upgrade Topic started 30 Jul 2020 15:22, by dvn4life1972 Last Post 30 Jul 2020 15:47 by dvn4life1972	Replies:2 Views:852	dvn4life1972 Last Post by dvn4life1972 30 Jul 2020 15:47
PlasmaC Will Not Move Z Topic started 30 Jul 2020 01:38, by dvn4life1972 Last Post 30 Jul 2020 02:37 by dvn4life1972	Replies:6 Views:873	dvn4life1972 Last Post by dvn4life1972 30 Jul 2020 02:37
Cut rules Topic started 27 Jul 2020 18:26, by CBEAR Last Post 29 Jul 2020 23:18 by CBEAR 1 2 3	Replies:21 Views:3752	CBEAR Last Post by CBEAR 29 Jul 2020 23:18
Material Settings Glitch Topic started 16 Feb 2020 21:52, by snowgoer540 Last Post 26 Jul 2020 12:11 by snowgoer540 1 2 3 ... 10	Replies:94 Views:12.4k	Last Post by snowgoer540 26 Jul 2020 12:11
Help with homing on dual axis PlasmaC Topic started 16 Jul 2020 21:43, by Clive S Last Post 26 Jul 2020 06:38 by Clive S 1 2 3 ... 7	Replies:65 Views:8646	Clive S Last Post by Clive S 26 Jul 2020 06:38
Using Spotting with Sheetcam Topic started 21 Jul 2020 18:39, by Clive S Last Post 23 Jul 2020 12:25 by phillc54 1 2 3 4	Replies:34 Views:5100	Last Post by phillc54 23 Jul 2020 12:25
Error Recovery Topic started 18 Jun 2020 07:16, by phillc54 Last Post 23 Jul 2020 12:21 by tommylight 1 2 3 ... 10	Replies:92 Views:11.4k	Last Post by tommylight 23 Jul 2020 12:21
Ohmic Enable Check Box Topic started 22 Jul 2020 21:34, by snowgoer540 Last Post 23 Jul 2020 10:14 by snowgoer540 1 2	Replies:10 Views:2565	Last Post by snowgoer540 23 Jul 2020 10:14
i cant open plasmac from Sample Configurations > by_machine > plasmac Topic started 21 Jul 2020 00:20, by Himarc3D Last Post 22 Jul 2020 02:22 by phillc54	Replies:3 Views:988	Last Post by phillc54 22 Jul 2020 02:22
Plamsac air scribe set up Topic started 19 Jul 2020 03:35, by CBEAR Last Post 21 Jul 2020 10:23 by snowgoer540 1 2	Replies:18 Views:3302	Last Post by snowgoer540 21 Jul 2020 10:23
Unknown m code used: M190 Topic started 21 Jul 2020 05:41, by CFE Last Post 21 Jul 2020 06:53 by phillc54	Replies:7 Views:1471	Last Post by phillc54 21 Jul 2020 06:53
Upgrade problems Topic started 13 Jul 2020 23:39, by CFE Last Post 20 Jul 2020 12:36 by tommylight 1 2	Replies:19 Views:2762	Last Post by tommylight 20 Jul 2020 12:36
New Configuration Error Topic started 12 Jul 2020 19:31, by snowgoer540 Last Post 20 Jul 2020 12:29 by Clive S 1 2 3 ... 5	Replies:40 Views:6153	Clive S Last Post by Clive S 20 Jul 2020 12:29
Cant find plasmac to configure Topic started 17 Jul 2020 23:11, by kramerda Last Post 17 Jul 2020 23:52 by phillc54	Replies:5 Views:832	Last Post by phillc54 17 Jul 2020 23:52
Steppers or DC motor for Z axis THC Topic started 16 Jul 2020 13:36, by kramerda Last Post 16 Jul 2020 16:28 by tommylight	Replies:3 Views:1066	Last Post by tommylight 16 Jul 2020 16:28
Torch Breakaway and Torch Pulse Topic started 13 Jul 2020 18:32, by snowgoer540 Last Post 16 Jul 2020 12:02 by snowgoer540 1 2 3 ... 5	Replies:41 Views:5564	Last Post by snowgoer540 16 Jul 2020 12:02
Plasma no ARC OK and torch fires when machine is turned on Topic started 13 Jul 2020 05:06, by luftlupus Last Post 16 Jul 2020 01:32 by luftlupus 1 2 3	Replies:22 Views:3963	Last Post by luftlupus 16 Jul 2020 01:32
THCAD-300 Jumper Topic started 10 Jul 2020 18:24, by KaleD Last Post 11 Jul 2020 11:00 by tommylight	Replies:7 Views:2587	Last Post by tommylight 11 Jul 2020 11:00

Time to create page: 0.179 seconds